483369

AEG VL 5527 MS Manual

24
Zoom out
Zoom in
Previous page
1/42
Next page
English
24
Intended Use
This device is intended for use as a fan for rooms of up
to 40m in size.
It is intended exclusively for this purpose and may only
be used as such. It may only be used in the manner
described in these instructions for use. The device must
not be used for commercial purposes.
Any other use of this device is considered to be contrary
to the intended use and may result in damage to materi-
als or even personal injury.
The  rm ETV - Elektro-Technische Vertriebsgesellschaft
mbH does not accept any liability for damage caused as
a result of the use of this device contrary to its intended
use.
Unpacking the Device
• Remove the device from its packaging.
• Remove all of the packaging material such as foils,
lling material, cable holders and cardboard packag-
ing.
• Check the scope of delivery.
ޥ NOTE:
There may still be dust or production residues on the
surface of the device. We recommend that you quickly
wipe o the housing with a damp cloth.
Assembly instructions
The device must be completely assembled before use!
While reading the text it is advisable to refer to the
„Overview of the Components“.
1. Place the stand tube (9) in the base (10).
2. Insert the weight (11) and the washer (12) on the
underside of the base (10).
3. Tighten the fastening screw (13) in a clockwise direc-
tion.
4. Place the motor (4) on the stand tube as shown in Il-
lustration B. The square recess on the holder (7) must
be positioned above the lower drill hole of the stand
tube.
5. Push the carriage bolt (22) through the lower hole as
far as the rectangular end stop.
6. The angle of inclination of the blower is  xed with
the knurled screw (23) and the retaining screw (20).
7. Then tighten the knurled screw (21) on the end of the
carriage bolt (22).
8. Position the rear protection grid (15) in place in ac-
cordance with the recesses.
ޥ NOTE:
Please ensure that the carrying handle is facing
upwards.
9. Turn the attachment ring (16) for the rear protection
grid (15) slightly in a clockwise direction.
10. Place the propeller in position and tighten it with the
retaining screw (2).
CAUTION:
The screw (2) has to be positioned on the  attened
section!
11. Attach the front protection grid (18) by inserting the
hook (1) with the groove into the rear protection
grid.
ޥ NOTE:
Ensure that the holes for the attachment screw in
the front and rear protective grille are aligned one
above the other.
12. Close the attachment hooks .
13. Secure the protection grid with the fastening screw
(19) and the nut (14).
Position
The ideal position is a non-slip,  at surface.
Putting into Service
Electrical Connection
1. Before inserting the plug into the socket. Make sure
that the mains voltage to be used matches that of
the device. You can  nd this information on the
nameplate.
2. Connect the device to a duly installed 230V/50Hz
protective contact socket.
Use
Basic Settings
Set the blower inclination angle before starting the
device (see point 6 of the assembly instructions).
Height Adjustment
• Release the knurled screw (8) on the stand tube.
• Move the blower to the desired height.
• Retighten the knurled screw.
Rotary Switch
On the rotary switch you can select the following set-
tings:
o 1 slow
o 2 medium
o 3 fast
o 0 o
Shift to „0“ to switch o the device.
05-VL 5527 MS.indd 2405-VL 5527 MS.indd 24 24.11.2008 9:46:47 Uhr24.11.2008 9:46:47 Uhr
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG VL 5527 MS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG VL 5527 MS in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info