Manual AEG TS 55 E (page 19 of 101) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

463236

Zoom out

Zoom in

1/101

English

Maintain a rm grip with both hands on the saw and position

your arms to resist kickback forces. Position your body to

either side of the blade, but not in line with the blade.

Kickback could cause the saw to jump backwards, but kickback forces

can be controlled by the operator, if proper precautions are taken.

When blade is binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless in

the material until the blade comes to a complete stop. Never

attempt to remove the saw from the work or pull the saw

backward while the blade is in motion or kickback may occur.

Investigate and take corrective actions to eliminate the cause of blade

binding.

When restarting a saw in the workpiece, centre the saw blade

in the kerf and check that saw teeth are not engaged into the

material. If saw blade is binding, it may walk up or kickback from

the workpiece as the saw is restarted.

Support large panels to minimise the risk of blade pinching

and kickback. Large panels tend to sag under their own weight.

Supports must be placed under the panel on both sides, near the line

of cut and near the edge of the panel.

Do not use dull or damaged blades. Unsharpened or improperly

set blades produce narrow kerf causing excessive friction, blade

binding and kickback.

Blade depth and bevel adjusting locking levers must be tight

and secure before making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

Use extra caution when making a „plunge cut“ into existing

walls or other blind areas. The protruding blade may cut objects

that can cause kickback.

Function of the guard

Check guard for proper closing before each use. Do not

operate the saw if guard does not move freely and enclose

the blade instantly. Never clamp or tie the guard with the

blade exposed. If saw is accidentally dropped, guard may be bent.

Check to make sure that guard moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

Check the operation and condition of the guard return spring.

If the guard and the spring are not operating properly, they

must be serviced before use. Guard may operate sluggishly due

to damaged parts, gummy deposits, or a build-up of debris.

Assure that the guide plate of the saw will not shift while

performing the “plunge cut” when the blade bevel setting

is not at 90°. Blade shifting sideways will cause binding and likely

kick back.

Always observe that the guard is covering the blade before

placing saw down on bench or oor. An unprotected, coasting

blade will cause the saw to walk backwards, cutting whatever is in its

path. Be aware of the time it takes for the blade to stop after switch

is released.

Riving knife function

Use the appropriate riving knife for the blade being used. For

the riving knife to work, it must be thicker than the body of the blade

but thinner than the tooth set of the blade.

Adjust the riving knife as described in this instruction

manual. Incorrect spacing, positioning and alignment can make the

riving knife ineective in preventing kickback.

Always use the riving knife, even when „plunge cutting“.

The riving knife is being pressed upwards during plunge cutting and

springs back automatically into the kerf after plunge cutting when

you move the saw forward.

For the riving knife to work, it must be engaged in the

workpiece. The riving knife is ineective in preventing kickback

during short cuts.

Do not operate the saw if riving knife is bent. Even a light

interference can slow the closing rate of a guard.

Wear ear protectors. Exposure to noise can cause hearing loss.

Use protective equipment. Always wear safety glasses when

working with the machine. The use of protective clothing is

recommended, such as dust mask, protective gloves, sturdy non-slip

footwear, helmet and ear defenders.

The dust produced when using this tool may be harmful to health.

Do not inhale the dust. Use a dust absorption system and wear a

suitable dust protection mask. Remove deposited dust thoroughly,

e.g. with a vacuum cleaner.

Always disconnect the plug from the socket before carrying out any

work on the machine.

Only plug-in when machine is switched o.

Keep mains lead clear from working range of the machine. Always

lead the cable away behind you.

Before use check machine, cable, and plug for any damages or

material fatigue. Repairs should only be carried out by authorised

Service Agents.

Do not use inserted tools not corresponding to the key data given in

these instructions for use.

Please do not use abrasion disks in this machine!

When sawing aluminium, the following measures must be taken for

safety reasons:

- Pre-connect a residual current device (FI, RCD, PRCD.

- Connect the machine to a suitable dust extractor.

- Clean the machine regularly of dust deposits in the motor housing

and in the protective cover.

- Aluminium must only be sawed with the special saw blades

designed for this purpose.

- When sawing panels, they must be lubricated with petroleum,

thin-walled pro les (up to 3 mm) can be sawed without lubrication.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG TS 55 E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG TS 55 E Manual

Product: