Manual AEG TBS TB 50 THERMO BODEN (page 20 of 76) (English, German, Dutch, French)

648290

Zoom out

Zoom in

1/76

Installation – for qualied contractors

9.4 Laying out the heating mat

Material losses

Do not cut, squash or kink the heating conductor on

the heating mat.

You may shorten and extend the cold lead as long

as you do not change its cross-section.

Material losses

» Do not use nails or other metal objects to attach

the heating mat to the oor.

» Only stand on the heating mat if absolutely nec-

essary. Take any necessary protective meas-

ures to avoid mechanical damage (e.g. shoes

with rubber soles).

Material losses

» Do not install the heating mat through or be-

neath insulating material.

» The installed heating mat may not cross expan-

sion joints in the oor.

» Do not use penetrating xing materials in the

vicinity of the heating mat, e.g. screws and rawl

plugs for door stoppers, WC ttings.

Observe the position of the heating mat specied in the

installation diagram for the subsequent steps.

» Lay out the heating mat in accordance with the in-

stallation diagram. The self-adhesive side must be

facing downwards.

26_07_29_0094_

» Cut the heating mat backing fabric with scissors at

the turning point. Make sure that you don't acciden-

tally damage the heating conductor with the scissors.

Material losses

The heating conductor bending radius must be at

least 18 mm. The smallest permissible bending radi-

us is six times the diameter of the heating conductor.

» Carefully bend the heating conductor at the cutting

point.

» Observe minimum distances (see chapter "Prepara-

tions / Safety clearances").

» Make sure that the temperature sensor lead does

not cross or touch the heating conductor and that the

temperature sensor is halfway between two heating

conductor loops.

» Make sure that heating mats do not overlap. Overlap-

ping heating mats may lead to malfunctions.

» Make sure that the fabric is laid out without any

creases.

» Press the heating mat rmly onto the oor.

9.5 Test measurement 2

After laying out the heating mat, check the total resistance

and insulation resistance of the heating mat to rule out the

possibility of damage to the heating mat.

Note

The warranty is not valid without proof of this meas-

urement.

» Measure the total resistance and insulation resist-

ance of the heating mats.

» Check whether the measured values are in the per-

missible measuring range (see chapter "Specica-

tion / Data table").

» Enter the measured values on the warranty card.

» Replace the damaged heating mat if the measured

values deviate from the permissible range.

9.6 Laying the oor covering

Material losses

Only use tile adhesive and levelling compound

which are suitable for underoor heating systems

and which can withstand constant temperatures of

at least 80 °C.

Material losses

When applying tile adhesive and levelling com-

pound, please observe the manufacturer's instruc-

tions concerning drying time and other manufactur-

er's information.

Note

You must wait at least 3 days, depending on the hu-

midity levels within the building, before starting to

lay the oor covering.

9.6.1 Tiles

» Select an appropriate tile adhesive or levelling com-

pound if applicable. Note that this must be able to

withstand constant temperatures of at least 80 °C.

» Seal the conduits so that tile adhesive cannot get

into the conduits whilst installing the heating mats.

26_07_29_0004_

1 Substrate with thermal insulation

2 Heating mat with heating conductor

3 Tile adhesive

4 Floor covering

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG TBS TB 50 THERMO BODEN in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 12,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG TBS TB 50 THERMO BODEN Manual

Product: