Manual AEG TBS TB 50 THERMO BODEN (page 19 of 76) (English, German, Dutch, French)

648290

Zoom out

Zoom in

1/76

Installation – for qualied contractors

8.4 Test measurement 1

Before installation, please check the total resistance and

insulation resistance of the heating mats in their delivered

condition.

Note

The warranty is not valid without proof of this meas-

urement.

» Measure the total resistance and insulation resist-

ance of the heating mat.

» Check whether the measured values are in the per-

missible measuring range (see chapter "Specica-

tion / Data table").

» Enter the measured values on the warranty card.

8.5 Preparing the substrate

» Make sure that the substrate is clean, dry, solid and

free from dirt and grease.

» Make sure that no sharp edges or pointed objects

are protruding from the oor. These could damage

the heating conductor.

» If the substrate is not level, carry out levelling oper-

ations so as to avoid cavities beneath the heating

conductor. Settlement joints in the substrate must not

be bridged using the heating mat.

9. Installation

9.1 Installing a ush box

Please install all power cables in a ush box for connec-

tion to the temperature controller.

Material losses

In bathrooms and wet rooms, the ush box must only

be installed outside safety zone 2.

26_07_29_0009_

1 Distribution cable (NYM 3x1.5 mm

)

2 Flush box

3 Conduit for temperature sensor

4 Temperature sensor

5 Cold lead / conduit for cold lead

» Choose an appropriate position to install the ush

box.

» Install an additional ush box if you would like to con-

nect more heating mats.

» Always install an additional ush box if the cold lead

or temperature sensor lead is too short.

9.2 Installing temperature sensors

The temperature sensor must be installed in a conduit.

The conduit is included as standard in the set.

» Choose an appropriate position for installing the con-

duit. Observe the instructions in chapter "Installation

diagram / Position of the temperature sensor".

» Install the conduit and insert the temperature sensor

into it.

9.3 Installing the cold lead

You can install the cold lead in a conduit or ush with the

oor in a groove in the screed.

9.3.1 Installing in a conduit

Material losses

The cold lead must be installed in a separate con-

duit. The cold lead and the temperature sensor lead

must not be installed in the same conduit.

» Install an additional conduit and install the cold lead

in the conduit.

» Make sure that the female connection for the heating

conductor/cold lead is not subjected to a tensile load

of more than 120 N.

9.3.2 Installation in the oor

Material losses

If installed in the oor, the cold lead must be able to

be inserted in the ush box without an extension.

The cold lead may not cross or touch the heating

conductor.

» Chisel out a groove in the screed by using appropri-

ate tools and install the cold lead in this groove.

» Make sure that the female connection for the heating

conductor/cold lead is not subjected to a tensile load

of more than 120 N.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG TBS TB 50 THERMO BODEN in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 12,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG TBS TB 50 THERMO BODEN Manual

Product: