648290
17
Zoom out
Zoom in
Previous page
1/76
Next page
17
Installation – for qualied contractors
INSTALLATION
6. Safety
Only a qualied contractor should carry out installation,
commissioning, maintenance and repair of the appliance.
6.1 General safety instructions
We guarantee trouble-free operation and operational re-
liability only if the accessories intended for the appliance
are used.
6.2 Instructions, standards and regulations
!
Material losses
Never install the heating mat on highly or normally
ammable materials.
!
Material losses
Never switch on the heating mat when it is rolled up.
Note
Observe all applicable national and regional regula-
tions and instructions.
7. Appliance description
The heating mat is a surface heating element. The heating
mat comprises a heating conductor which is coiled over
a self-adhesive fabric.
The heating mat is glued directly to the screed or to level-
ling compound (e.g. oating screed). The heat generated
by the heating mat is thus transferred directly to the oor.
The required oor temperature is set via an external
temperature controller. The temperature controller is
equipped with a temperature sensor. The temperature
sensor must be installed at heating level.
26_07_29_0100_
321
4
5
1 Heating conductor
2 Temperature sensor
3 Conduit (tube for installing the temperature sensor)
4 Female connection for heating conductor/cold lead
5 Cold lead (electrical power cable)
The heating mat is switched on or off according to the
oor temperature set on the temperature controller.
The temperature controller takes account of heat gain,
e.g. due to sunlight or lighting, and provides frost pro-
tection.
The temperature controller is self-monitoring. In the event
of a power failure, sensor break or sensor short-circuit,
the heating automatically switches off.
7.1 Standard delivery
TBS TB 50 160/1-8
Heating mat
Two type plate labels (warranty card / main junction
box)
TBS TB 50 Set 160/1-8
Heating mat
Conduit (ø 10 mm) with sensor well
Anti-kink bend
Temperature controller FRTD 903
Temperature sensor
Two type plate labels (warranty card / main junction
box)
7.2 Warranty card / installation diagram
You must complete the warranty card and installation di-
agram fully. The warranty is not valid without this proof.
The chapter “Preparations” contains information on com-
pleting the installation diagram.
8. Preparations
8.1 Installation site / Installation conditions
!
Material losses
Do not install the heating mat at temperatures below
5 °C.
Note
In new builds, allow the screed to cure for 4-6 weeks.
Only install the heating mat once this period has
ended.
8.1.1 Substrate
!
Material losses
The heating mat may only be installed on oors.
Walls or ceilings may not be used as installation
surfaces.
You may install the heating mat on a variety of substrates,
e.g. screed, hot mix asphalt or moisture-resistant chip-
board. Observe the following information:
Installation on hot mix asphalt: The substrate must
be able to withstand temperatures of approx. 80 °C.
Installation on chipboard: Suitable insulation boards
can also be installed to improve impact sound
insulation.
Very sandy screed surfaces must be coated with an
adhesive dispersion.
Thermal insulation
Thermal insulation must be tted between the unnished
oor and the heating mat.
» Please ensure that the thermal insulation complies
with the latest standards.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG TBS TB 50 THERMO BODEN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG TBS TB 50 THERMO BODEN in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 12,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info