640805

AEG T65278AC Manual

66
Zoom out
Zoom in
Previous page
1/76
Next page
the above buttons until the symbol go
out of view.
You can activate the child lock function:
• before you push the Start/Pause
(Start/Pauze) button - the appliance
cannot start
• after you push the Start/Pause (Start/
Pauze) button - all the push buttons
and the programme dial are deactiva-
ted
7.14 At the end of programme
When the drying cycle is completed, the
symbol flashes on the display. If the
Buzzer (Zoemer) function is on, an acous-
tic signal sounds intermittently for one
minute.
To remove the laundry:
1.
Push the On/Off (Aan/Uit) button for
2 seconds to deactivate the appli-
ance.
2.
Open the appliance door.
3.
Remove the laundry.
4.
Close the appliance door.
After each drying cycle:
• clean the filter
• drain the water container
(See chapter CARE AND CLEANING.)
8. HINTS AND TIPS
8.1 Ecological hints
• Do not use fabric softener to wash and
then dry. In the tumble dryer laundry
becomes soft automatically.
• Use the condensate as distilled water,
e.g. for steam ironing. If necessary
clean the condensate before (e.g. with
a coffee filter) to remove possible
small pieces of fluff.
• Always keep the airflow slots on the
bottom of the appliance clear.
• Use the load volumes specified in the
programmes chapter.
• Make sure that is good airflow in the
appliance installation position.
• Clean the filter after each drying cycle.
• Spin good the laundry before drying.
8.2 Water hardness and
conductivity
Water hardness can be different for dif-
ferent locations. Water hardness has an
effect on the water conductivity and the
operation of the conductivity sensor in
the appliance. If you know the value of
the water conductivity you can adjust the
sensor to dry with the better results.
To change the sensor conductivity:
1.
Turn the programme dial to availa-
ble programme.
2.
Push at the same time the Delicate
(Behoedzaam) and Anticrease (Anti-
kreuk) buttons and hold down until
one of the these symbols go into
view on the display:
–
low conductivity <300 μS/
cm
–
moderate conductivity
300-600 μS/cm
–
high conductivity >600
μS/cm
3.
Push the Start Pause button again
and again until you set necessary
level.
4.
To memorise setting push at the
same time the Delicate (Behoed-
zaam) and Anticrease (Anti-kreuk)
buttons.
8.3 Water container full —
indication
By default the indication LED is always
on. It comes into the view at the end of
the cycle or when the water container is
full. When you use an external equip-
ment to drain the container, the LED can
be off.
To activate or deactivate the indication:
1.
Turn the programme dial to availa-
ble programme.
2.
Push at the same time the Delicate
(Behoedzaam) and Delay Start (Star-
66
www.aeg.com
… 66 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG T65278AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG T65278AC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info