648288
8
Zoom out
Zoom in
Previous page
1/56
Next page
8
Installation - für den Fachhandwerker
15. Wartung
WARNUNG Stromschlag
Führen Sie alle elektrischen Anschluss- und Instal-
lationsarbeiten nach Vorschrift aus.
WARNUNG Stromschlag
Trennen Sie vor allen Arbeiten das Gerät allpolig von
der Netzspannung.
Wenn Sie das Gerät entleeren müssen, beachten Sie das
Kapitel „Gerät entleeren“.
15.1 Sicherheitsventil prüfen
» Lüften Sie das Sicherheitsventil an der Sicherheits-
gruppe regelmäßig an, bis der volle Wasserstrahl
ausläuft.
15.2 Gerät entleeren
WARNUNG Verbrennung
Beim Entleeren kann heißes Wasser austreten.
Falls der Speicher für Wartungsarbeiten oder bei Frost-
gefahr zum Schutz der gesamten Installation entleert
werden muss, gehen Sie folgendermaßen vor:
» Schließen Sie das Absperrventil in der
Kaltwasserzuleitung.
» Öffnen Sie die Warmwasserventile aller
Entnahmestel len.
» Entleeren Sie das Gerät über die Sicherheitsgruppe.
15.3 Schutzanode kontrollieren /
austauschen
» Kontrollieren Sie die Schutzanode erstmalig nach
2 Jahren und tauschen Sie sie ggf. aus. Beachten
Sie dabei den maximalen Übergangswiderstand zwi-
schen Schutzanode und Behälter. Falls der Einbau
einer Stabanode von oben nicht möglich ist, installie-
ren Sie eine Gliederanode.
» Entscheiden Sie danach, in welchen Zeitabständen
die weiteren Prüfungen durchgeführt werden.
15.4 Gerät reinigen und entkalken
» Verwenden Sie keine Entkalkungspumpe.
» Entkalken Sie den Heizansch nur nach Demon tage
und behandeln Sie die Speicheroberäche und die
Schutzanode nicht mit Entkalkungsmitteln.
Anzugsdrehmoment der Flanschschrauben siehe Kapitel
Technische Daten / Maße und Anschlüsse“.
15.5 Heizansch austauschen
26_02_09_0069_
5
6
4
23
1
1 Dämmplatte
2 Flanschplatte
3 Lötansch
4 Isolierplatte
5 Korrosionsschutz-Widerstand 390 Ω
6 Dichtung
Der Korrosionsschutz-Widerstand dient als Potenzialab-
gleich und verhindert Stromaustritts-Korrosion an den
Heizkörpern.
» Der Korrosionsschutz-Widerstand darf bei Service-
arbeiten nicht beschädigt oder entfernt werden.
» Bauen Sie nach Austausch des Korrosions-
schutz-Widerstandes den Heizansch wieder ord-
nungsgemäß zusammen.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG STM 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG STM 30 in the language / languages: German, Dutch, French as an attachment in your email.

The manual is 5,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info