463222

AEG ST 400 Manual

6
Zoom out
Zoom in
Previous page
1/62
Next page
5
ENGLISH
ST 400, ST 440, STEP 420, STEP 450, SPE 70, SPE 80 A
1. Set the stroke and pendulum stroke according to the material to be cut.
2. Position the machine with the front part of the base plate on the material, and
switch on.
3. Press the machine downwards onto the material and guide it along the cutting line.
Do not press down too hard on the piece you are cutting. Light pressure on the saw
blade is sufficient to achieve the optimum rate of sawing.
When cutting along a score line, use the marking on the anti-splintering device as an
optical guide.
To obtain a perfectly straight cut, clamp a strip of wood as a guide along the material
or use the parallel guide (accessory).
For cutting at an angle, or cutting a bevel, adjust the base plate.
For sawing close to the edge, set the base plate at its rearmost position.
To avoid vibration, clamp metal sheets onto a wooden base.
To saw metal, use cooling agents along the cutting line (oil, white spirit).
Plunge cuts without pre-drilling a hole are possible with soft materials (wood, light
building materials for walls). Harder materials (metals) must first be drilled with a hole
corresponding to the size of the saw blade.
Move the base plate to the rearmost setting in order to obtain the best possible
cutting angle for starting the cut.(see section ”Adjusting the base plate”)
1. Set the pendulum stroke at the pendulum stroke control to “0”.
2. Without switching the machine on, place it with the front edge of the base plate on
the cutting point.
3. Switch the machine on and carefully lower the saw blade already running into the
material.
GERMANY
274315
STEP 500
electronic
III
II
I
0
GERMANY
274315
STEP 500
electronic
III
II
I
0
GERMANY
274315
STEP 500
electronic
III
I
I
I
0
The anti-splintering device almost entirely
prevents the edge of the wood from
splintering.
Place the anti-splintering device as shown
in the illustration with the smooth side
downwards and flush with the base plate
(this is only possible with the base plate in
the forward position).
*Not included in standard equipment,
available as an accessory.
Advice for
operation
Hints
Sawing sheet
metal
Plunge cuts
Anti–splintering
device
(Accessory*)
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG ST 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG ST 400 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info