Manual AEG PW 5644 FA (page 37 of 70) (English, German, Dutch, French, Italian, Polish, Spanish)

551916

Zoom out

Zoom in

1/70

English

This device has been tested according to all relevant current

CE guidelines, such as electromagnetic compatibility and low

voltage directives, and has been constructed in accordance

with the latest safety regulations.

Information about the Analysis Scale

WARNING:

Do not use the scales if you use a pacemaker or another

medical implant with electronic components. The function

of the implant may be impaired by the measurement.

The main principle of this device is based on the measure-

ment of the electric impedance within the human body. In

order to determine the actual body data, the device leads a

weak, unnoticeable electric signal through your body.

The signal is generally safe! However, please read our special

safety instructions!

The method of measurement is referred to as “bioelectric

impedance analysis” (BIA), a factor which is based on the re-

lationship between body weight and associated body water

percentages as well as on other biological data (age, gender,

body weight).

Use

NOTE:

• You will nd the buttons for the operation on the top

edge of the scale.

• The scales are factory set with the units “kg” and “cm”.

To change the settings to “lb” or “st:lb”as well as “ft:in”,

proceed as follows:

• Switch the scales on by applying gentle pressure on the

glass surface with your foot or toe.

• Press the UP button

, until the required unit of weight

is displayed. The unit for the height also automatically

changes.

Weighing Function

• Place the scale on a hard, at surface (avoid carpets). An

uneven ﬂoor contributes to inaccurate measurements.

• Stand on the scales with both feet. The device switches

on automatically.

• Distribute your weight equally and wait for the scale to

determine your weight.

• The digits on the display will ash before your exact

weight will be shown.

• In order to extend the battery life, the device will auto-

matically turn off 15 seconds after you have stepped off

the scale.

• If there is no weight determination while “0.0” is shown,

the scale will shut off automatically after 15 seconds.

Saving Personal Data

NOTE:

• The scale has default values that you can change, as

described below.

• Carry out the following steps in sequence and within a

few seconds. Otherwise, the device will automatically

cancel input mode.

• Press the button SET. The memory space (P0) will ﬂash on

the display. Conﬁrm the setting by pressing SET or select

another memory space by pressing the UP / DOWN but-

ton. Then press SET to go to the next setting.

• The symbol for “male” or “female” will ash. Conrm the

setting by pressing SET or use the UP / DOWN button to

choose the symbol for your gender. Then press SET to go

to the next setting.

• The height setting will ash. Select your height by press-

ing UP or DOWN button. Holding down one of the

buttons will accelerate the process. Conﬁrm your entry by

pressing SET.

• The setting AGE will ash. Select your age by pressing UP

or DOWN button. Holding down one of the buttons will

accelerate the process. Conﬁrm your entry by pressing

SET.

• The short display “- - - -” will terminate the entry mode

for this memory location. Then you will see the memory

location, the symbol of the gender and the weight

“0.0 kg” (0.0 lb / 0: 0 st:lb) in the display.

You now have the following options:

• You can change the units for weight and type. Press the

UP button

, until the desired unit of weight is displayed.

The unit for the height automatically changes.

• Press the SET button to see the selected settings again.

• Allocate further memory spaces. There are 10 spaces

available in total. Press SET and change the space by

pressing the UP or DOWN button. Proceed further as

described above.

• If you want to make changes, press SET (the memory

location will blink). Select the stored position using the UP

or DOWN button. Proceed further as described above.

• You can immediately start measuring.

Measurement and Analysis

Record your personal data in the memory.

NOTE:

• The analysis scale will only work correctly when you are

standing on the contact surfaces barefoot and with

slightly moistened foot soles, if possible. Completely

dry foot soles can lead to unsatisfactory results as they

have a conductivity that is too low.

• If necessary wipe the contact surfaces to improve

results.

Hey! 4 different people with big variety of weight, height, age, gender etc tried to use the scale but the same message showed up to all of us ”Err2”. In the manual it Said that it might be because of the body fat content lies above or below the limits of the measuring scale. But in fact we know that our body fat percentace lies within the acceptable range. So is there anything we can do to fix this or is it possible that the scale was broken when we recieved it? Submitted on 25-12-2019 at 13:49
Reply Report abuse
- I had the same problem. You need stand still on the scale when its calculating your bodyfat. Then it worked for me Answered on 21-8-2020 at 18:09
  Vote up (1) Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG PW 5644 FA in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG PW 5644 FA Manual

Product: