Manual AEG PSB300 (page 50 of 64) (English, German, Dutch, French, Italian, Spanish)

563600

Zoom out

Zoom in

1/64

To remove belt cover

1. Remove the two (2) screws (A) securing belt cover (B) to frame (C).

2. Remove belt cover.

• Replace belt cover by installing cover and screws and tighten se-

cure ly.

Entfernen der riemenabdeckung

1. Entfernen Sie die zwei (2) Schrauben (A), mit denen die Riemena-

beckung (B) am Rahmen (C) befestigt ist.

2. Entfernen Sie die Riemenabdeckung.

• Befestigen Sie die Riemenabdeckung erneut, indem Sie die Abdeck-

ung und die Schrauben wieder anbringen und die Schrauben fest

anziehen.

To replace belts

The auger and traction drive belts are not adjustable. If the belts are dam-

aged or begin to slip from wear, they should be replaced. It is recommended

that the belt(s) be replaced by a qualiﬁ ed service center.

NOTE: It is recommended that both the auger and traction drive belt be

replaced at the same time.

The V-belts on your snow thrower are of special construction and should

be replaced by original equipment manufacturer (OEM) belts available

from your nearest dealer. Using other than OEM belts can cause personal

injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow

thrower. While separating the auger housing (1) from the frame

assembly (2), it is important that an assistant stand in the op er -

at ing position and hold the snow thrower handles (3). Serious

personal injury and/or damage to the unit could occur if the snow

thrower should fall during the belt chang ing process.

1. REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel

tank into a suitable container, outdoors, away from ﬁ re or ﬂ ame. Wipe

up any spilled gasoline.

2. REMOVE DISCHARGE CHUTE - Loosen lock nut securing chute rota-

tor head to mounting bracket only enough to allow chute rotator head

to be raised and discharge chute to be removed from snow thrower.

3. REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this

section of this manual.

4. REMOVE ENGINE PULLEY (A) - Remove bolt (B), lock washer (C)

and ﬂ at washer (D) securing pulley to engine crankshaft. Remove

outside (auger) pulley (A) only from crankshaft.

5. SEPARATE SNOW THROWER - With your assistant standing in the

operating position holding the handles, remove the two bolts (F) and

lock washers (G) holding auger housing (1) and frame (2) together.

WARNING: As the last bolt is removed, have your assistant care-

ful ly lower the handles down to the ground.

6. REMOVE AUGER BELT (H) from around pulley (E).

7. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER (J) and

remove traction drive belt (K) from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole

in idler arm (J) and rotate ratchet clockwise to relieve tension.

2 1

Pour enlever le couvercle de la courroie

1. Enlevez les deux (2) vis (A) en ﬁ xant le couvercle de la

courroie (B) au châssis (C).

2. Enlevez le couvercle de la courroie.

• Remplacez le couvercle de la courroie en installant le

couvercle et serrez solidement.

Desmontar el cubre correas

1. Desmontar los dos (2) tornillos (A) que sujetan el cubre

correas (B) a la carcasa (C).

2. Desmontar el cubre correas.

• Sustituir el cubre correas colocando la cubierta y los

tornillos y apretando ﬁ rmemente.

Het verwijderen van de riemhuls

1. Verwijder de twee (2) schroeven (A) die de riemhuls (B)

aan het frame (C) bevestigen.

2. Verwijder de riemhuls.

• Zet de riemhuls weer terug door de huls en de schroeven

terug te plaatsen en draai stevig aan.

Rimuovere il coperchio della cinghia

1. Togliere le due (2) viti (A) che ﬁ ssano il coperchio della

cinghia (B) all’intelaiatura (C).

2. Togliere il coperchio della cinghia.

• Rimettere coperchio e viti, stringendo bene.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG PSB300 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG PSB300 Manual

Product: