551733
7
Zoom out
Zoom in
Previous page
1/11
Next page
AEG installation manual
7
1) The 90° inlet elbow may be installed only together with the mounting
bracket and the inlet valve. Anywhere else in the tubing system, 90°
sweep elbows and 45° elbows should be used. (Fig. A and B)
2) Tubes are cut straight so that the cutting line is not slanted. Use a miter
saw if possible. Cut edges can be fi nished with a knife (to remove burrs).
3) For tubing joints, use suitable PVC glue to make the fi ttings secure and
tight. Apply a thin and even layer of glue only to the end of the tube – not
to the sleeve. This will prevent the glue from overfl owing to the end face
of the tubing. Close the glue can carefully immediately after use and make
sure to have adequate ventilation during installation. Avoid inhaling glue
vapors. Insert the tube all the way into the sleeve while turning it at the
same time (Fig. C).
4) The inlet is made through the fi re wall according to Fig.fi gure E or by
using a 2” (50mm) diameter fi re cuff (Fig. D). Check the inlet with a fi re
authority.
mounting bracket
90° elbow
90°
sweep
elbow
A
B
Tubing System Installation
Important notes for installation!
correct
incorrect
incorrect
pipe collars are attached
to the wall
wire mesh
concrete
sand
vacuum pipe electrical tube
2” (51 mm)
re stopping pipe
collars
E
F
correct
correct
incorrect
D
min. 3/4” (18 mm)
push the pipe completely into the fi tting
C
Begin the main tube installation with the farthest inlet valve and place the
tubes temporarily at fi rst. Do not glue the joints yet until you have made
sure that the tubing routing is correct. The glue will dry quickly; therefore,
the joints have to be fi tted right after applying the glue.
When measuring the tubes, take into account that the tube goes appro-
ximately 2/3” (18mm) into the sleeve and approximately 7/8” (20mm) into
the extension tube.
The tubing system can also be installed in a fl oor that will be concrete
casted later on (Fig. F). In such cases, the low-voltage cable must be
protected by a conduit pipe. The conduit pipe should be attached to the
vacuum tube or the casting net. For the vacuum tube, the routing channel
has to be 2” wide (51mm). The ends of the vacuum tubes and the con-
duit pipes should be plugged before concrete casting.
vacuum pipe
wall
vacuum pipe
min. 7 7/8”
(200 mm)
protects the combustible
building material
steel protective sleeve
min. 1/ 16” (2 mm)
wall
Installation Examples
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG Oxygen - K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG Oxygen - K in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG Oxygen - K

AEG Oxygen - K User Manual - English, German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info