464380
11
Zoom out
Zoom in
Previous page
1/22
Next page
11
For the Fitter
Ö Screw the hexagonal screws (7) into the drilled holes up to the point at which the natural stone
heating unit with the open slotted holes in its wall mountings (2) can still be hooked on behind
the screw head.
Ö Hang the natural stone heating unit (do not allow to topple or tilt – danger of breakage) and
tighten up the hexagonal screws. In this process, take care to ensure that any stresses which
occur are compensated for by slightly loosening the securing screws (6) in the natural stone
slab.
These should subsequently be retightened up to the stop point (overtightening can cause
dowels to become loose).
2.5.2 Electrical connection
Connect the natural stone heating unit only to a 230 V 50 Hz alternating current supply.
If the mains connection lead is shortened, take care to ensure that the natural stone heating unit
can be taken off again, even without disconnecting the connection lead.
2.6 First start-up
When the natural stone heating unit is heated up for the first time, a heating-up time of
20 minutes should not be exceeded. The slab must then cool down for at least 60 minutes.
This measure is to be repeated one further time.
In the first two days, the heating should be built up to the desired room temperature in stages.
This avoids hairline cracks developing. If hairline cracks should nevertheless develop, this is not
dangerous and impairs neither the functioning nor the safety of the natural stone heating unit.
2.7 Handover
Explain the functions of the unit to the user. Draw his or her attention to the safety instructions,
in particular.
Hand the operating and installation instructions to the user.
2.8 Special accessories
Control of the natural stone heating unit is effected using the room thermostat.
RT 500: Room thermostat with thermal feedback, switching capacity 10 A 250 V.
RT 600: Room thermostat with thermal feedback, switching capacity 10 A 250 V.
RT 601 SN: Room thermostat with thermal feedback, with power switch ON/OFF,
switching capacity 10 A 250 V.
RTE 900 SN: Electronic single-circuit controller with power switch ON/OFF,
switching capacity 16 A 250 V.
English
3. Guarantee
For guarantee please refer to the respective terms and conditions of supply for your country.
The installation, electrical connection and first operation of this appliance should be carried
out by a qualified installer.
The company does not accept liability for failure of any goods supplied which are not
installed in accordance with the manufacturer's instructions.
3.1 Environment and recycling
Please help us to protect the environment by disposing of the packaging in accordance with the
national regulations for waste processing.
3.1.1 Recycling of obsolete appliances
Appliances with this label must not be disposed off with the general waste. They must be
collected separately and disposed off according to local regulations.
02 Inhalt NSH.p65 19.05.2005, 12:1111
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG NSH 65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG NSH 65 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info