565732
9
Zoom out
Zoom in
Previous page
1/48
Next page
- 8 -
Nadelklammerschraube
Needle clamp screw
Nadelklammer
Needle clamp
Hinunter
Down
Herauf
Up
Locker
Loose
Fest
Tight
AUSRICHTEN DER MASCHINE / LEVELING THE MACHINE
AUSWECHSELN DER NADEL / REPLACING NEEDLE
1. Schalten Sie die Maschine aus.
2. Stellen Sie die Nadel in die höchste Position.
3. Lockern Sie die Nadelklammerschraube. Entfernen Sie die alte Nadel.
4. Ersetzen Sie eine Nadel, wenn sie verbogen oder beschädigt ist, durch
eine neue Nadel.
5. Stecken Sie die Nadel - mit der flachen Seite von Ihnen abgewandt – bis
zum Anschlag in den Nadelschaft.
6. Drehen Sie die Nadelklammerschraube richtig fest.
1. Turn off power.
2. Raise needle to its highest position.
3. Loosen needle clamp screw, remove the old needle.
4. If any needle is deformed, bent or damaged, replace with a new needle.
5. With the flat side of the needle facing away from you, insert needle as far
up as it will go.
6. Tighten the needle clamp screw securely.
Um festzustellen, ob eine Nadel verbogen ist, legen Sie diese mit der
flachen Seite nach unten auf eine ebene Fläche (eine Nadelplatte, ein
Stück Glas, etc.). Die Lücke zwischen der Nadel und der ebenen Fläche
sollte gleichmäßig sein.
Benutzen Sie niemals eine verbogene oder zerbrochene Nadel. Dies
kann zum Auslassen von Stichen oder zum Reißen des Fadens führen.
Beschädigte Nadeln können den Stoff ruinieren.
Kaufen Sie immer Nadeln mit einer guten Qualität. Tauschen Sie die
Nadel regelmäßig aus.
To determine if the needle is bad, place the flat side of the needle on
something flat (a needle plate, piece of glass, etc.). The gap between the
needle and the flat surface should be even.
Never use a bent or broken needle. It may cause skipped stitches or
thread breakage. Bad needles can ruin the fabric.
Always purchase good quality needles. Change needle often.
Wenn die Nähmaschine nicht fest steht, entfernen Sie den Nähtisch und
stellen Sie die Maschine, wie in der Abbildung dargestellt, ein.
If the sewing machine is not level, remove the sewing table and adjust the
leveling by turning the foot as illustrated.
Flache Seite von Ihnen
abgewandt.
Flat face side away from you
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG NM 680 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG NM 680 in the language / languages: English, German as an attachment in your email.

The manual is 3,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info