526974
38
Zoom out
Zoom in
Previous page
1/52
Next page
symbol come into view on the dis-
play. To deactivate push again the
above buttons until the symbol go out of
view.
You can activate the child lock function:
before you push the Start/Pause but-
ton - the appliance cannot start
after you push the Start/Pause button
- all the push buttons and the pro-
gramme dial are deactivated
7.14 Starting a programme
To activate the programme push the
Start/Pause button. The LED above the
push button changes the colour to red.
7.15 Change a programme
To change a programme, push the On/
Off (Aan/Uit) button to deactivate appli-
ance. Push the On/Off (Aan/Uit) to acti-
vate the appliance and then set the pro-
gramme again.
7.16 At the end of programme
When the drying cycle is completed, the
symbol flashes on the display. If the
Buzzer (Zoemer) function is on, an acous-
tic signal sounds intermittently for one
minute.
To remove the laundry:
1.
Push the On/Off (Aan/Uit) button for
2 seconds to deactivate the appli-
ance.
2.
Open the appliance door.
3.
Remove the laundry.
4.
Close the appliance door.
After each drying cycle:
clean the filter
drain the water container
(See chapter CARE AND CLEANING.)
8. HINTS AND TIPS
8.1 Ecological hints
Do not use fabric softener to wash and
then dry. In the tumble dryer laundry
becomes soft automatically.
Use the condensate as distilled water,
e.g. for steam ironing. If it is necessary
clean the condensate before (e.g. with
a coffee filter) to remove possible
small pieces of fluff.
Always keep the airflow slots on the
bottom of the appliance clear.
Use the load volumes which are speci-
fied in the programmes chapter.
Make sure that is good airflow in the
appliance installation position.
Clean the primary filter after each dry-
ing cycle.
Clean the heat exchanger filters when
the applicable indicator comes into
the view on the control panel.
Spin good the laundry before drying.
8.2 Water hardness and
conductivity
Water hardness can be different for dif-
ferent locations. Water hardness has an
effect on the water conductivity and the
operation of the conductivity sensor in
the appliance. If you know the value of
the water conductivity you can adjust the
sensor to dry with the better results.
To change the sensor conductivity:
1.
Turn the programme dial to availa-
ble programme.
2.
Push at the same time the Dry Plus
(Drogen Plus) and the Anticrease
(Anti-kreuk) buttons. Hold down until
one of the symbols go into view on
the display:
38
www.aeg.com
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG LAVATHERM 75370AH2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG LAVATHERM 75370AH2 in the language / languages: English, German as an attachment in your email.

The manual is 7,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG LAVATHERM 75370AH2

AEG LAVATHERM 75370AH2 Manual - Dutch - 1 pages

AEG LAVATHERM 75370AH2 User Manual - Dutch, French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info