775049
23
Zoom out
Zoom in
Previous page
1/56
Next page
9.3 AutoDose basic setting
The factory pre-set doses for a large
load are 90 ml for detergent tank and
25 ml for fabric softener tank: the
optimal configuration to meet majority
of use condition. Based on this
setting, the appliance will calculate
the precise dosage for each wash.
However, under extreme conditions (very
soft or very hard water) and particular
type of detergent (such as super
compact), we recommend to adjust the
pre-set dosage by following the
indication given on detergent and fabric
softener container: e.g when using super
compact detergent you may need to
reduce the pre-set dosage considerably.
If the washing results are not satisfying
or there is too much foam during
washing, you may need to change the
factory setting. Read in the paragraph
'AutoDose configuration mode' how to
change the basic setting, but before:
1. Identify the water hardness level.
Check the water hardness level in
your area. The levels are generally
indicated as: soft, medium and hard.
If necessary, please contact your
local water authority to check the
water hardness in your area.
2. Identify the customized detergent
dosage.
Check the label in the detergent/
fabric softener container suggesting
the quantity to use. This suggestion
is measured combining three
different factors:
Water hardness level (see the
following table);
Normal soil level;
Rated capacity of the appliance
(e.g. maximum load capacity 9
kg). If the rated capacity on the
product container refers to lower
capacity appliances, the
customized dosage should be
increased.
Water hardness levels
Levels Water hardness range
°f1) °d2) °e3) mmol/l ppm
Soft <15 <8 <10 <1.4 <140
Medium4) 15 - 25 8 - 14 0 - 17 1.5 - 2.5 150 - 250
Hard >25 >14 >17 >2.5 >250
1) French degrees
2) German degrees
3) English degrees
4) Factory setting, able to satisfy most of the use conditions.
9.4 AutoDose configuration
mode
Enter the AutoDose
configuration mode before
proceeding with any
programme setting. The
configuration mode may
cancel temporary settings .
1. Press the On/Off button for a few
seconds to activate the appliance.
2. Wait about 10 seconds for appliance
internal check.
3. To enter in configuration mode, hold
pressed the Temp. and the Spin
buttons simultaneously for a few
seconds until the display shows the
on the left in the display and
blinking detergent tank and
softener tank indicators on the
right in the display.
ENGLISH 23
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG L6FBG941CA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG L6FBG941CA in the language / languages: English as an attachment in your email.

The manual is 1.86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info