698118
13
Zoom out
Zoom in
Previous page
1/84
Next page
13
ENGLISH
8. INSTALLATION INSTRUCTIONS
8.1. Before installation
Check that the input voltage indicated on
the characteristics plate is the same as
the voltage of the power outlet you are
going to use.
Open the drawer and take out all the
accessories and remove the packing
material.
Attention! The front surface of the
crockery heater may be wrapped in a
protective film. Before using the crockery
warmer for the first time, remove this film
carefully.
Make sure that the crockery warmer is
not damaged in any way. Check that the
drawer opens and closes correctly. If you
find any damage, contact the Technical
Assistance Service.
Attention: the power socket should be
easily accessible after the crockery
warmer has been installed.
The crockery warmer should only be built-
in in combination with those appliances
indicated by the manufacturer. If it is fitted
in combination with other appliances, the
guarantee is no longer valid since it is
impossible to guarantee that the crockery
warmer will work correctly.
8.2. Installation
To build-in the crockery warmer in
combination with another appliance there
must be a fixed, interim shelf in the
housing unit to support the weight of both
appliances.
The appliance to be combined with the
crockery warmer will be placed directly on
the latter without any need to have a
separating shelf.
To build-in the appliance which is
combined with the crockery warmer,
follow the instructions set out in the
respective instructions and fitting booklet.
The relevant installation dimensions are
indicated in mm in the diagrams shown at
the end of this booklet. Proceed as
follows:
1. Place the crockery warmer on the
shelf and slide it towards the interior
of the niche in such a way that it is
centred and completely lined up with
the front of the unit.
2. Check that the crockery warmers
frame is properly levelled and is
sitting evenly on the shelf.
3. Open the drawer and fix the crockery
warmer to the sides of the unit using
the provided screws.
8.3. Electrical Connection
Electrical installation must be performed
by an electrician qualified in accordance
with the legislation in force.
Before connecting the crockery warmer to
the electric mains, check that the voltage
and frequency of the mains matches that
which is shown on the rating plate located
in the heating block inside.
The electric connection is made via an
omnipolar switch, which is suitable for the
intensity to be tolerated and which has a
minimum gap of 3mm between its
contacts, which will ensure
disconnection in case of emergency or
when cleaning the crockery warmer.
If a plug is used for the electric
connection, then it must be accessible
after installation.
The connection should include correct
earthing, in compliance with current
norms.
WARNING: THE CROCKERY
WARMER MUST BE EARTHED.
If the flexible supply cable fitted to the
crockery warmer ever needs to be
changed, it should be replaced by an
official After Sales Service, because it
requires special tools.
The manufacturer and retailers do not
accept responsibility for any damage that
may be caused to people, animals or
property if these installation instructions
are not observed.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG KDE912922 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG KDE912922 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info