382757
2
Zoom out
Zoom in
Previous page
1/52
Next page
1
ENGLISH
HK 46 N
You have high standards and expect to purchase quality goods – quality offered by
Atlas Copco.
We have built a durable and reliable electric power tool for you.
Please read the instructions for use before first operation so you can handle your
power tool effectively and safely.
We are sure that buying an AEG Electric Power Tool from Atlas Copco was the right
choice!
Nominal power 630 W. . . . . . . . . . . . . . . . . . . . .
No-load speed 4600 min
-1
. . . . . . . . . . . . . . . . . . . .
Saw blade dia. x hole dia 152x20 mm. . . . . . . . .
Cutting depth at 90° 46 mm. . . . . . . . . . . . . . . . . .
Cutting depth at 45° 30 mm. . . . . . . . . . . . . . . . . .
Weight 2,6 kg. . . . . . . . . . . . . . . . . . . . . . . . . . . .
J Please pay attention to the safety instructions in the attached leaflet!
J Always disconnect the plug from the socket before carrying out any work on the
machine.
J Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
J Sawdust and splinters must not be removed while the machine is running.
J Before use check machine, cable, and plug for any damages or material fatigue.
Repairs should only be carried out by authorised Service Agents. Keep mains lead
clear from working range of the machine. Always lead the cable away behind you.
J Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
J Dust that arises when working in wood or using the tool on industrial material can be
dangerous to health. In this case connect the tool to a suction device (e.g. Atlas
Copco absorbtion system AS 3 W).
J Always use the protective shields on the machine.
J Before switching on ensure that protective swing cover moves freely.
J Mind safety regulations issued by your employer’s liability insurance association.
Do not use grinder on any material containing asbestos.
J Protective cover operation only with the provided lever resp. automatically by the
workpiece.
J When plunge cutting secure the workpiece against kickback (e.g. with cross bar).
J Do not use saw blades not corresponding to the key data given in these instructions
for use.
J Be careful not to saw into nails or similar objects.
J The riving knife should be adjusted so that:
- the distance between it and the tips of the saw blade teeth does not exceed 5 mm
- it is not more than 5 mm away from the lowest point of the tips of the saw blade
teeth.
J Do not use cracked or distorted saw blades or HSS saw blades (high speed steel).
J The teeth thickness, or the set of the teeth must be thicker than the body of the
blade and the riving knife. Do not remove the riving knife (exception: plunge cutting).
J Do not brake the speed of the saw-blade after switching off the motor by pressing
on it from the side.
J Do not clamp the swivel protection guard.
J Clamp wooden rods on both sides of the saw blade to prevent them from rotating.
J Do not fix the on/off switch in the ”on” position when using the saw hand-held.
J Typically the A-weighted noise levels of the tool are:
Sound pressure level = 94dB(A)Sound power level = 107dB(A). Wear ear
protectors!
J Typically the hand-arm vibration is below 2.5 m/s
2
.
Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG hk 46 n at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG hk 46 n in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info