21592
18
Zoom out
Zoom in
Previous page
1/32
Next page
GB
D
F
I
E
P
NL
DK
S
FIN
HBS 100
HBSE 100
Instructions for use
Please read and save these
instructions.
Gebrauchsanleitung
Bitte lesen und aufbewahren.
Instruction d’utilisation
Prière de lire et de conserver.
Istruzioni d’uso
Si prega di leggere le istruzioni e
di conservarle.
Instrucciones de uso
Lea y conserve estas
instrucciones por favor.
Instruções de serviço
Por favor leia e conserve em seu
poder.
Gebruiksaanwijzing
Lees en let goed op deze
adviezen.
Brugsanvisning
Vær venlight at læse og
opbevare.
Bruksanvisning
Var god läs och tag tillvara dessa
instruktioner.
Käyttöohje
Lue ja säilytö
2
ENGLISH
HBS 100, HBSE 100
You have high standards and expect to purchase quality goods – quality offered by
Atlas Copco.
We have built a durable and reliable electric power tool for you.
Please read the instructions for use before first operation so you can handle your
power tool effectively and safely.
We are sure that buying an AEG Electric Power Tool from Atlas Copco was the
right choice!
HBS 100 HBSE 100
Nominal power 1010 W 1010 W. . . . . . . . . . . . . . . . . . . . . . . . . . .
Belt speed no load 350 m/min 230–350 m/min. . . . . . . . . . . . . . . . . . .
Sanding width 100 mm 100 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Belt length 560 mm 560 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sanding surface 100 x 140 mm 100 x 140 mm. . . . . . . . . . . . . . . . .
Weight 4,2 kg 4,2 kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J Please pay attention to the safety instructions in the attached leaflet!
J Dust that arises when working in wood or using the tool on industrial material can be
dangerous to health. In this case connect the tool to a suction device (e.g. Atlas
Copco absorbtion system AS 3 W).
J Appliances used at many different locations including open air must be connected
via a current surge preventing switch.
J Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
J Sawdust and splinters must not be removed while the machine is running.
J Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
J Always disconnect the plug from the socket before carrying out any work on the
machine.
Only plug-in when machine is switched off.
J Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
J When sanding metal the dust suction facility should not be used, because of the risk
of fire from flying sparks.
Typically the A-weighted noise levels of the tool are:
Sound pressure level = 91 dB (A).
Sound power level = 104 dB (A).
Wear ear protectors!
Typically the hand-arm vibration is below 2.5 m/s
2
.
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is
possible as the appliance features protective insulation to DIN 57 740/ VDE 0740
and CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is
connected to the plug terminal marked L or coloured red, and the blue (neutral) wire
of this appliance is connected to the plug terminal marked N or coloured black.
Under no circumstances must the wires of this appliance be connected to the earth
terminal of the plug marked either E, with the earth symbol or coloured green or
green/yellow.
The belt sander can be used for sanding wood, plastics and metal.
Do not use this product in another way as stated for normal use.
Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
Mains
connection
Use
3
ENGLISH
HBS 100, HBSE 100
Always disconnect the plug from the
socket before carrying out any work on the
machine.
Prior the changing belt, adjust sanding belt
by turning the belt adjusting screw approx.
2–3 cm in the direction of the open side of
the machine beyond the rollers, whilst the
machine is running, as the new sanding
belt can sometimes brush against the
machine housing.
1. Pull the clamping lever forwards
2. Remove the worn belt and fit the inside of
the belt is pointing in the same direction as
the arrow on the machine.
3. Push the clamping lever back again
4. Taking a test run, position the sanding belt
with the aid of the belt adjusting screw so
that it is flush with the outer edge of the
sanding belt support.
The speed is adjusted by means of the
electronic thumb wheel.
A = lowest speed
F = highest speed
Brief description
Modifications: Text, diagrams and data are correct at the time of
printing. In the interest of continuous improvement of our products,
technical specifications are subject to alteration without prior notice.
Integrated dust removal
Locking button
On-/off switch
Suction connector
Adjusting screw for belt
Dust bag
Electronic thumb wheel (only
applicable for HBSE 100)
Changing the
belt
Setting speed of
rotation
(only applicable
for HBSE 100)
HBSE
electronic
4
ENGLISH
HBS 100, HBSE 100
Intermittent use
Switching on: Press On-/off switch
Switching off: Release On-/off switch
Continuous use
Switching on: Press the On-/off switch and
then the locking button, after that release
on-off switch.
Switching off: Press the On-/off switch and
then release.
Always hold machine firmly with both hand
prior to switching on. Only switch on in
raised position.
When sanding, guide the machine without applying special pressure. The weight of
the machine itself is quite sufficent for good sanding results.
When sanding wood, the dust bag should
be used.
When suction performance becomes less
effective empty dust bag.
For suction greater quantities of dust, an
adaptor can be fitted which enables a
suction hose to be used (available as
accessory). This can be connected to an
industrial vacuum cleaner.
When sanding metal the dust suction
facility should not be used, because of the
risk of fire from flying sparks.
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our AEG service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the ten–digit
No. as well as the machine type printed on the label and order the drawing at your
local service agents or directly at: Atlas Copco Electric Tools GmbH, Postfach 320,
D–71361 Winnenden.
The range of accessories with part numbers is shown in our catalogue.
Switching the
machine on and
off
Advice for
operation
Dust extraction
Maintenance
Accessories
HBSE
electronic
HBSE
electronic
2
1
HBSE
electronic
5
DEUTSCH
HBS 100, HBSE 100
Sie sind anspruchsvoll und erwarten Qualität, die Ihnen Atlas Copco bietet.
Für Sie haben wir ein haltbares und möglichst sicheres Elektrowerkzeug gebaut.
Bitte lesen Sie vor Inbetriebnahme Ihres Gerätes die Gebrauchsanleitung, um Ihr
Elektrowerkzeug effektiv und gefahrlos nutzen zu können.
Wir sind sicher, daß Sie mit AEG-Elektrowerkzeugen von Atlas Copco Ihre richtige
Wahl getroffen haben.
HBS 100 HBSE 100
Nennaufnahme 1010 W 1010 W. . . . . . . . . . . . . . . . . . . . . . . . . .
Bandgeschwindigkeit Leerlauf 350 m/min 230–350 m/min. . . . . . . . .
Schleifbreite 100 mm 100 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bandlänge 560 mm 560 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schleiffläche 100 x 140 mm 100 x 140 mm. . . . . . . . . . . . . . . . . . . .
Gewicht 4,2 kg 4,2 kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J Sicherheitshinweise der beiliegenden Broschüre beachten!
J Bei längerem Bearbeiten von Holz oder bei gewerblichem Einsatz für Materialien, bei
denen gesundheitsgefährdende Stäube entstehen, ist das Elektrowerkzeug an eine
geeignete Absaugvorrichtung anzuschließen (z.B. Atlas Copco Absaugsystem
AS 3 W). (In Deutschland werden für Holzstäube aufgrund TRGS 553 geprüfte
Absaugeinrichtungen gefordert).
Für andere Materialien muß der gewerbliche Betreiber die speziellen Anforderungen
mit der zuständigen Berufsgenossenschaft klären.
J Steckdosen in Außenbereichen müssen mit Fehlerstrom-Schutzschaltern
ausgerüstet sein. Das verlangt die Installationsvorschrift für Ihre Elektroanlage. Bitte
beachten Sie das bei der Verwendung unseres Gerätes – sprechen Sie mit Ihrem
Elektroinstallateur.
J Beim Arbeiten mit der Maschine stets Schutzbrille tragen. Schutzhandschuhe, festes
und rutschsicheres Schuhwerk und Schürze werden empfohlen.
J Späne oder Splitter dürfen bei laufender Maschine nicht entfernt werden.
J Gehäuse der Maschine nicht anbohren, da sonst die Schutzisolierung unterbrochen
wird (Klebeschilder verwenden).
J Vor allen Arbeiten an der Maschine Stecker aus der Steckdose ziehen.
Maschine nur ausgeschaltet an die Steckdose anschließen.
J Anschlußkabel stets vom Wirkungsbereich der Maschine fernhalten. Kabel immer
nach hinten von der Maschine wegführen.
J Beim Schleifen von Metall wegen Brandgefahr durch Funkenflug keine
Staubabsaugung verwenden.
Der A-bewertete Geräuschpegel des Gerätes beträgt typischerweise:
Schalldruckpegel = 91 dB (A).
Schalleistungspegel = 104 dB (A).
Gehörschutz tragen!
Die Hand-Arm Vibration ist typischerweise niedriger als 2,5 m/s
2
.
Nur an Einphasen-Wechselstrom und nur an die auf dem Leistungsschild
angegebene Netzspannung anschließen. Anschluß ist auch an Steckdosen ohne
Schutzkontakt möglich, da eine Schutzisolierung nach DIN 57 740/ VDE 0740 bzw.
CEE 20 vorliegt. Die Funkentstörung entspricht der Europanorm EN 55014.
Der Bandschleifer ist geeignet zum Flächenschleifen von Holz, Kunststoff und Metall.
Dieses Gerät darf nur wie angegeben bestimmungsgemäß verwendet werden.
Vorwort
Technische
Daten
Hinweise für
Ihre Sicherheit
Geräusch-
meßwerte
Vibrations-
meßwerte
Netzanschluß
Verwendung
6
DEUTSCH
HBS 100, HBSE 100
Vor allen Arbeiten an der Maschine
Stecker aus der Steckdose ziehen.
Vor dem Schleifbandwechsel das
Schleifband etwas zur offenen
Maschinenseite hin verstellen, da das
neue Schleifband unter Umständen am
Maschinengehäuse streifen kann; hierzu
Bandjustierschraube bei laufender
Maschine nach rechts drehen.
1. Entspannhebel nach vorn ziehen.
2. Verbrauchtes Band entnehmen und neues
Band aufziehen. Darauf achten, daß die
Pfeilrichtung auf der Inneseite des Bandes
mit dem Pfeil auf der Maschine
übereinstimmt.
3. Entspannhebel wieder einklappen.
4. Maschine einschalten und das Schleifband
mit der Bandjustierschraube so ausrichten,
das es mit der äußeren Kante der
Schleifbandauflage abschließt.
Die Drehzahl mit dem Elektronik-Stellrad
einstellen.
A = kleinste Drehzahl
F = größte Drehzahl
Kurzbeschreibung
Änderungen: Text, Bild und Daten entsprechen dem technischen
Stand zur Zeit des Drucktermins. Änderungen im Sinne der
Weiterentwicklung unserer Produkte sind vorbehalten.
Integrierte Staubabsaugung
Arretierknopf für Schalterdrücker
Schalterdrücker
Absaugstutzen
Justierschraube für Bandlauf
Staubsack
Stellrad Drehzahl (nur bei HBSE 100)
Schleifband
wechseln
Drehzahl
einstellen
(nur bei
HBSE 100)
HBSE
electronic
7
DEUTSCH
HBS 100, HBSE 100
Momentschaltung
Einschalten: Ein-/Ausschalter drücken.
Ausschalten: Ein-/Ausschalter loslassen.
Dauerschaltung
Einschalten: Ein-/Ausschalter drücken und
dann Arretierknopf drücken,
Ein-/Ausschalter loslassen.
Ausschalten: Ein-/Ausschalter drücken
und loslassen.
Maschine schon vor dem Einschalten fest
mit beiden Händen festhalten.
Einschalten nur in abgehobener Position.
Maschine beim Schleifen ohne Druck führen. Das Eigengewicht der Maschine
genügt für gute Schleifergebnisse.
Zum Schleifen von Holz den Staubsack
verwenden.
Bei nachlassender Saugleistung den
Staubsack entleeren.
Bei großen Staubmengen kann auch über
einen Adapter ein Saugschlauch
angeschlossen werden. Der Saugschlauch
kann an einen Atlas Copco Naß- und
Trockensauger oder Rüttelsauger
angeschlossen werden.
Beim Schleifen von Metall wegen
Brandgefahr durch Funkenflug keine
Staubabsaugung verwenden.
Stets die Lüftungsschlitze der Maschine sauber halten.
Nur AEG Zubehör und Ersatzteile verwenden. Bauteile, deren Austausch nicht
beschrieben wurde, bei einer AEG Kundendienststelle auswechseln lassen
(Broschüre Garantie/Kundendienstadressen beachten).
Bei Bedarf kann eine Explosionszeichnung des Gerätes unter Angabe der
Maschinen Type und der zehnstelligen Nummer auf dem Leistungsschild bei Ihrer
Kundendienststelle oder direkt bei Atlas Copco Electric Tools GmbH, Postfach 320,
D–71361 Winnenden angefordert werden.
Das Zubehör mit Bestellnummern ersehen Sie bitte aus unseren Katalogen.
Ein-/Ausschalten
Arbeitshinweise
Staubabsaugung
Wartung
Zubehör
HBSE
electronic
HBSE
electronic
2
1
HBSE
electronic
8
FRANÇAIS
HBS 100, HBSE 100
Vous avez des exigences et vous voulez de la qualité – une qualité que vous offre
Atlas Copco.
Nous avons mis au point pour vous un outil électrique de longue durée vous offrant
un maximum de sécurité. Avant la mise en service de votre appareil, veuillez lire
attentivement le mode d’emploi afin d’en tirer le plus d’efficacité et d’éviter tout risque
de danger.
Nous sommes convaincus qu’avec les outils électriques Atlas Copco vous avec fait
le choix qu’il fallait.
HBS 100 HBSE 100
Puissance absorbée 1010 W 1010 W. . . . . . . . . . . . . . . . . . . . . .
Vitesse de bande à vide 350 m/min 230–350 m/min. . . . . . . . . . . . . .
Largeur de la bande 100 mm 100 mm. . . . . . . . . . . . . . . . . . . . . . . .
Longueur de la bande 560 mm 560 mm. . . . . . . . . . . . . . . . . . . . . . .
Surface de ponçage 100 x 140 mm 100 x 140 mm. . . . . . . . . . . . .
Poids 4,2 kg 4,2 kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J Respecter les instructions de sécurité se trouvant dans le prospectus ci-joint.
J Lors de travaux de ponçage de longue durée, bois ou autres matériaux dégageant
des poussières nocives pour la santé, la machine est à raccorder à un appareil
d’aspiration (Atlas Copco AS 3 W).
J Les prises de courant se trouvant à l’extérieur doivent être équipées de disjoncteurs
de protection, répondant ainsi à la prescription de mise en place de votre installation
électrique. Veuillez, d’une part, en tenir compte lors de l’utilisation de notre appareil
et d’autre part, en parler à votre électricien.
J Toujours porter des lunettes protectrices lorsqu’on travaille avec la machine. Des
gants de sécurité et un masque de protection sont recommandés.
J Ne jamais enlever les copeaux ni les éclats lorsque la machine est en marche.
J Ne pas percer le carter de la machine; ceci pourrait entraîner une détérioration de
l’isolation de protection (utiliser des autocollants).
J Avant tous travaux sur la machine extraire la fiche de la prise de courant.
Ne raccorder la machine au réseau que si l’interrupteur est en position arrêt.
J Le câble d’alimentation doit toujours se trouver en dehors du champ d’action de la
machine. Toujours maintenir le câble d’alimentation à l’arrière de la machine.
J En raison des risques d’incendie, il est déconseilléd’avoir recours au sysréme
d’aspiration pour le ponçage des métaux.
Les mesures réelles (A) des niveaux de bruit de la machine sont:
Intensité de bruit = 91 dB (A).
Niveau de bruit = 104 dB (A).
Toujours porter des casques protecteurs!
La vibration de l’avant–bras est en–dessous de 2,5 m/s
2
.
Nos machines fonctionnent uniquement sur courant alternatif monophasé. S’assurer
que la tension du réseau correspond effectivement à celle indiquée sur la plaque
signalétique de la machine. Le branchement sur une prise de courant sans mise à
terre est possible du fait de la double isolation selon normes DIN 57 740/VDE 0740
et CEE 20. Antiparasitage selon normes européennes EN 55014.
La ponceuse a bande peut-être utilisée pour poncer le bois, les plastiques et le
métal.
Comme déjà indiqué, cette machine n’est conçue que pour une utilisation normale.
Introduction
Caractéristiques
techniques
Conseils de
sécurité
Mesure de bruit
Valeur de
vibration
mesurée
Branchement
secteur
Utilisation
9
FRANÇAIS
HBS 100, HBSE 100
Avant tous travaux sur la machine extraire
la fiche de la prise de courant.
Mettre la machine en route. Tourner la vis
d’ajustage vers la droite et faire glisser la
bande vers l’extérieur d’environ 2à 3cm.
Arrêter la machine.
1. Tirer le lever vers l’avant.
2. Enlever la bande et la remplacer. Veiller à
faire corresspondre le sens des flèches qui
se trouvent sur la bande et sur la machine.
3. Repousser le lever.
4. Mettre en route et positionner la bande au
moyen de la vis.
La vitesse se règle au moyen de la
molette.
A = Vitesse réduite
F = Vitesse élevée
Description
Modifications: Les textes, les illustrations et les données
techniques correspondent à la situation au moment de l’impression.
Toutes modifications techniques sont réservées dans le cadre du
développement technique permanent.
Aspiration intégrée de la poussière
Bouton de blocage
Interrupteur
Manchon d’aspiration
Vis de réglage de la bande
(centrage)
Sac à poussières
Molette de réglage de la vitesse
électronique (potentiomètre)
(uniquement sur HBSE 100)
Remplacement
de la bande
Reglage de la
vitesse
(uniquement sur
HBSE 100)
HBSE
electronic
10
FRANÇAIS
HBS 100, HBSE 100
Marche momentanée
Mise en marche: appuyer sur l’interrupteur
Marche/Arrêt
Arrêt: lâcher l’interrupteur Marche/Arrêt
Marche continue
Mise en marche: appuyer d’abord sur
l’interrupteur marche/arrêt puis sur le
bouton de blocage, lâcher l’interrupteur
marche/arrêt.
Arrêt: appuyer sur l’interrupteur
marche/arrêt et lâcher.
Avant la mise en route, maintenir la
machine en l’air avec les deux mains.
Il n’est pas nécessaire, lors du ponçage, d’exercer une pression particulière sur la
machine, son propre poids suffit.
Pour le poncage du bois, utiliser le sac à
poussières.
Si le rendement de l’aspiration baisse,
vider le sac.
Pour les travaux dégageant beaucoup de
poussière, il est possible, tant en utilisation
portative que stationnaire, de raccorderla
ponceuse à l’aspirateur NTE 1100, RSE
ou tout aspirateur industriel. Pour se faire,
utiliser un adaptateur et un tuyau (en
option).
En raison des risques d’incendie, il est
déconseilléd’avoir recours au sysréme
d’aspiration pour le ponçage des métaux.
Tenir toujours propre les orifices de ventilation de la partie moteur.
N’utiliser que des pièces et accessoires AEG. Pour des pièces dont l’échange n’est
pas décrit, s’adresser de préférence aux stations de service après-vente AEG (voir
brochure Garantie/Adresses des stations de service après-vente).
Si besoin est, une vue éclatée de l’appareil peut être fournie. S’adresser, en
indiquant bien le numéro à dix chiffres porté sur la plaque signalétique, à votre
station de service après–vente (voir liste jointe) ou directement à Atlas Copco
Electric Tools GmbH, B.P. 320, D–71361 Winnenden.
Consulter nos catalogues qui vous renseignent sur notre programme d’accessoires
avec leur référence.
Mise en
marche/arrêt
Conseils
pratiques
Aspiration de la
poussière
Entretien
Accessoires
HBSE
electronic
HBSE
electronic
2
1
HBSE
electronic
11
ITALIANO
HBS 100, HBSE 100
La vostra richiesta ed aspettativa è quella di acquistare merce d’elevata qualità -
qualità offerta da Atlas Copco.
Noi costruiamo per voi utensili elettrici durevoli e affidabili.
Si prega di leggere attentamente le istruzione al primo utilizzo cosicché si possa
utilzzare l’utensile elettrico in modo più sicuro e corretto.
Siamo sicuri che acquistare gli utensili elettrici AEG di Atlas Copco sia la scelta
migliore.
HBS 100 HBSE 100
Potenza assorbita 1010 W 1010 W. . . . . . . . . . . . . . . . . . . . . . . .
Velocità a vuoto 350 m/min 230–350 m/min. . . . . . . . . . . . . . . . . . . . .
Larghezza levigatura 100 mm 100 mm. . . . . . . . . . . . . . . . . . . . . . . .
Lunghezza nastro 560 mm 560 mm. . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensioni levigtura 100 x 140 mm 100 x 140 mm. . . . . . . . . . . . .
Peso 4,2 kg 4,2 kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J Si prega di leggere con attenzione le istruzioni riguardanti la sicurezza, nel volantino
allegato.
J Per lunghe lavorazioni nel legno o con altri materiali che producono poveri dannose
alla salute, e’ prescritto l’utilizzo sull’utensile dell’aspirazione polvere (Atlas Copco
AS 3 W).
J Gli apparecchi mobili usati all’aperto devono essere collegati interponendo un
interruttore di sicurezza per guasti di corrente.
J Durante l’uso dell’apparecchio utilizzare sempre gli occhiali di protezione. Inoltre si
consiglia di usare sistemi di protezione per la respirazione e per l’udito, oltre ai guanti
di protezione.
J Non rimuovere trucioli o schegge mentre l’utensile è in funzione.
J Evitare di forare la carcassa dell’utensile per non danneggiare l’isolamento.
(Utilizzare placchette adesive).
J Prima di effettuare qualsiasi lavoro sulla macchina togliere la spina dalla presa di
corrente.
Inserire la spina solo con interruttore su posizione “OFF”.
J Tenere sempre lontano il cavo di collegamento dall’area di lavoro dell’attrezzo.
J Per levigatura di metallo non aspirare la polvere causa scintille e pericolo di incendio.
La misurazione A del livello di rumorosità di un utensile è di solito:
Livello di rumorosità = 91 dB (A).
Potenza della rumorosità = 104 dB (A).
Utilizzare le protezioni per l’udito!
Le vibrazioni sull’elemento mano-braccio di solito sono inferiori a 2.5 m/s
2
.
Alimentazione dell’utensile: corrente alternata monofase. Importante: la tensione
della rete deve corrispondere a quella riportata sulla targhetta dell’utensile. Il
collegamento é possibile anche con prese non munite di contatto di protezione: é
previsto infatti un isolamento di protezione conforme a norme DIN 57740/VDE 0740
(CEE 20). La schermatura contro i radiodisturbi é conforme alla norma
europea EN 55014.
La levigatrice a nastro è adatta per trattare superfici piane di legno, plastica e
metallo.
Utilizzare il prodotto solo per l’uso per cui è previsto.
Premessa
Dati tecnici
Norme di
sicurezza
Livello di
rumorosità
Livello di
vibrazione
Collegamento
alla rete
Possibilità’ di
utilizzo
12
ITALIANO
HBS 100, HBSE 100
Prima di effettuare qualsiasi lavoro sulla
macchina togliere la spina dalla presa di
corrente.
Per evitare che il nuovo nastro tocchi
carcassa della levigatrice, girare verso
destra la vite con apparecchio funzionante,
fare sporgere il nastro da sosituire ca. 2-3
cm oltre i rulli e verso il lato esterno
dell’apparecchio.
1. Tirare la leva in avanti, togliere il nastro da
sostituire e montare quello nuova.
2. Fare attenzione che la direzione della
freccia sul lato interno del nastro sia rivolta
nella stessa direzione di quella sulla
levigatrice.
3. Fare ritornare la leva nella posizione
orginale.
4. Con qualche giro di prova e attraverso la
vite di aggiustaggio portare il nastro in
positione da formare linea unica con il lato
esterno dell’appoggio nastro.
La velocità viene regolata attraverso la
rondella elettronica
A= bassa potenza
F= alta potenza
Breve indicazione
Modifiche: Testo, figure e dati corrispondono allo standard tecnico
aggiornato all’epoca della stampa. Ci riserviamo pertanto eventuali
modifiche tecniche dovute all’ulteriore sviluppo dei nostri prodotti.
Aspirazione integrata
Blocco interruttore
Interruttore
Attacco aspirazione
Vite aggiustaggio nasto
Sacchetto
raccoglipolvere
Regolatore elettronico (solo per HBSE 100)
Sostituzione
nastro
Impostare il
numero di giri
(solo per
HBSE 100)
HBSE
electronic
18
PORTUGUES
HBS 100, HBSE 100
Antes de efectuar qualquer intervenção na
máquina, tirar a ficha da tomada.
1. Puxe a patilha de aperto para a frente.
2. Retire a cinta utilizada e monte a parte de
dentro da cinta de tal modo que aponte na
mesma direcção da seta da máquina.
3. Empurre a patilha de aperto novamente.
4. Faça um pequeno teste, posicione a cinta
de lixagem com a ajuda do parafuso de
ajuste de tal maneira que coincida com as
arestas exteriores do suporte de da cinta.
Breve descrição
Alterações: Texto, figura e características correspondem ao
desenvolvimento técnico à data da impressão. Reservamo-nos o
direito de introduzir modificações nos nossos produtos com vista ao
seu aperfeiçoamento.
Dispositivo de sucção integrado
Botão de bloqueio
Interruptor
Ligação ao dispositivo de sucção
Parafuso de ajuste para a cinta
Saco de poeiras
(só nos HBSE 100)
Mudança da
cinta
Ajuste da
velocidade
de rotação
(só nos
HBSE 100)
HBSE
electronic
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG HBS100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG HBS100 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info