697512
11
Zoom out
Zoom in
Previous page
1/37
Next page
PT
GB
DE
AR
ES
FA
FR
GR
NL
www.aeg.com
3
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
The product stops
or does not start
The brushroll is blocked Clean and remove entangled hair, threads and bres from the brush roll.
The product might be
overheated
Turn o the vacuum cleaner. Then check if the nozzle, tube, hose or lters are blocked
and/or dirty. Let the product cool down for minimum 2 hours on the charging stand
before starting it again. If the product still is not working, please contact an authorized
AEG Service Centre.
The battery is empty (last
LED blinks)
Charge the vacuum cleaner.
Reduction or no
suction power
Filters / Nose Cone is dirty
or missing
- Clean or wash the lters and put them back (See also Instruction book section 7).
- Change or replace the lters (www.aeg.com/shop).
Air Channel / Cyclon is
blocked
- Remove the dust container and check the air channel and air inlet in the dust container
to see if something is stuck.
Floor nozzle is blocked - Remove Floor nozzle and check if something is stuck in the nozzle.
Hose is blocked
- Remove Floor nozzle and check if something got stuck in the hose. If so use a stick to
remove the obstacle. However, be careful in case the obstruction.
Note: The warranty does not cover any damage to the hose caused by cleaning it.
Water or other
liquids has been
sucked into the
product
- Stop the product and let it dry for 48h (do not put it in the charging stand!).
If the product is not working anymore it will be necessary to replace the motor at an
authorized AEG service centre.
Note: Damage to the motor caused by the penetration of water is not covered by the
warranty.
The product is not
charging
Main unit is in wrong
position
Push the main unit down to the lowest position. It should not be locked in the upper
position and/or in between.
Product is placed wrong in
the charging stand
Check if the connectors from the back of the main unit are connected to the charging
stand.
Charging pin is not
plugged in
Make sure charging pin is connected in the back of the charging stand, and charging
adapter is plugged in the socket.
Wrong or no nozzle
attached
Make sure the main oor nozzle is attached to the product or it will not charge.
To protect the battery and
electronics, charging will
not occur if room temper-
ature is below 5°C or over
35°C.
Store and charge the product indoor and in a room temperature between 5 - 35°C.
Charging is taking
longer than 6 hours
Room temperature is over
35°C
Charging time will be longer if the temperature is high, which is normal. Store and
charge the product in a normal room temperature.
Please also see Instruction book chapter 2.
Brushroll is not
rotating
Changing the oor nozzle
while product is running
After changing the nozzle restart the product.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG FX9-1-ANIM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG FX9-1-ANIM in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 6,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info