464432

AEG FRTD 903 montage Manual

2
Zoom out
Zoom in
Previous page
1/8
Next page
© 2010 OJ Electronics A/S - EHT Haustechnik GMBH
2
erreicht, um Deponien und die Umwelt zu
entlasten. Damit leisten wir gemeinsam einen
wichtigen Beitrag zum Umweltschutz.
RECYCLING VON ALTGERÄTEN
Geräte mit diesem Aufkleber dürfen
nicht mit dem normalen Hausmüll
entsorgt werden. Sie müssen
getrennt gesammelt und gemäß den
lokalen Vorschriften entsorgt werden.
TECHNISCHE DATEN
Spannung .................... 230 V AC ± 10%, 50 Hz
Max. Vorsicherung ....................................... 16 A
Eingebauter Schalter ..................... 2-polig, 16 A
Ausgangsrelais ...... Schließkontakt - SPST - NO
Ausgang ............................. Max. 16 A / 3600 W
Regelprinzip ........................................... PBM/PI
Bereitschaftsbetrieb ................................. 0,6 W
Batterie-Backup ..................................... 5 Jahre
Temperaturbereich ............................. +5/+40 °C
Begrenzungsfühler (OCD4) ................. +5/+40 °C
Umgebungsbetriebstemperatur ......... +0/+25 °C
Energie auslesung, genauigkeit ................... 2%
Verschmutzungsgradkontrolle .......................... 2
Nennimpulsspannung ................................. 4 kV
Schutzgrad .................................................. IP21
Abmessungen .................. H/84, B/84, T/40 mm
Einbautiefe ............................................... 20 mm
Display ................................... 100x64 Pixel STN
- Hintergrundbeleuchtung
EU Gebrauchsmuster ........... 001101349-0001/2
Der Thermostat ist wartungsfrei.
English
The thermostat is an electronic on/off thermo-
stat for temperature control by means of an
NTC sensor located either externally or inter-
nally within the thermostat.
The thermostat is for flush mounting in a wall
socket. A baseplate for external wall mounting
is available.
PRODUCT PROGRAMME
FRTD 903
(MCD4-1999) Clock-thermostat with 2 sensors.
Floor sensor and built-in room
sensor.
WARNING – Important Safety Instructions.
Disconnect the power supply before carrying
out any installation or maintenance work on this
control unit and associated components. This
control unit and associated components should
only be installed by a competent person (i.e. a
qualified electrician). Electrical installation must
be in accordance with appropriate statutory
regulations.
MOUNTING OF SENSOR
The floor sensor contains a safety extra-low
voltage (SELV) circuit, allowing it to be placed
as close to the floor surface as necessary with-
out having to take account of the risk of shock
should the sensor cable become damaged. The
two wires from the sensor to the mounting box,
must be additionally insulated, e.g. shrink flex.
To prevent loose cables from the fixed instal-
lation from coming into contact with the
terminal block for the floor sensor, they must be
restrained using cable ties.
It is recommended that the cable and sensor be
placed in a non-conductive installation pipe em-
bedded in the floor (fig. 3). The end of the pipe
must be sealed and the pipe placed as high as
possible in the concrete layer. Alternatively, the
sensor can be embedded directly in the floor.
The sensor cable must be led through a sepa-
rate pipe or segregated from power cables.
The floor sensor must be centred between the
heating cable.
The sensor cable may be extended up to 7 m
by means of a separate two-core cable. Two
vacant wires in a multi-core cable used, for
example, to supply current to the floor heating
cable must not be used. The switching peaks
of such current supply lines may create inter-
ference signals that prevent optimum controller
function. If a shielded cable is used, the shield
must not be connected to earth (PE). The two-
core cable must be placed in a separate pipe or
segregated from power cables.
MOUNTING OF THERMOSTAT
WITH BUILT-IN SENSOR
The room sensor is used for comfort tempera-
ture regulation in rooms. The thermostat should
be mounted on the wall approx. 1.6 m above
the floor in such a way as to allow free air circu-
lation around it. Draughts and direct sunlight or
other heat sources must be avoided (fig. 4). No
external sensor is connected.
Mounting of thermostat
1. Slide the power button down to Off “0”.
2. Release the front cover ONLY by inserting a
small screwdriver into the hole on either side
of the thermostat.
3. Connect the wires in accordance with the
diagram (fig. 2).
4. Mount the thermostat in the wall socket.
5. Fit the frame and carefully press the cover
onto the thermostat. Ensure that both the
power slide button on the cover and the
power switch pin are down.
DO NOT open the thermostat by releasing the
four fixing clips on the back.
First time settings:
The first time the thermostat is connected,
push the power slide button to On “I”. Lan-
guage, time and date must be set using the
buttons:
1. Set language
2. Set time
3. Set date
PROGRAMMING
See user manual.
FAULT LOCATION
If the sensor is disconnected or short-circuited,
the heating system is switched off. The sensor
can be checked against the resistance table
(fig. 5).
ERROR CODES
E0: Internal error. The thermostat must be
replaced.
E1: Built-in sensor short-circuited or
disconnected.
E2: External sensor short-circuited or
disconnected.
E5: Internal overheating. Inspect the installa-
tion.
CE MARKING
According to the following standard:
LVD/EMC: EN 60730-2-9
CLASSIFICATION
The product is a Class II device (enhanced
insulation) and must be connected to in the
following way:
Term. 1: Neutral (N
Term. 2: Phase (L) 230 V ±10%, 50/60 Hz
Term. 3–4: Load, max. 16 A / 3600 W
Term. X: Do not connect
Term. 5-6: External floor sensor
ENVIRONMENT AND RECYCLING
Please help us to protect the environment by
disposing of the packaging in accordance with
national regulations for waste processing.
RECYCLING OF OBSOLETE APPLIANCES
Appliances with this label must not
be disposed of with general
household waste. They must be
collected separately and disposed
of in compliance with local
regulations.
TECHNICAL DATA
Voltage ............................ 230 VAC ±10% 50 Hz
Max. pre-fuse .............................................. 16 A
Built-in circuit breaker .................... 2-pole, 16 A
Output relay ............. Make contact - SPST - NO
Output ................................ Max. 16 A / 3600 W
Control principle .................................... PWM/PI
Stand-by power ........................................ 0.6 W
Battery backup ....................................... 5 years
Temperature range .............................. +5/+40°C
Limit sensor (OCD4) ............................ +5/+40°C
Ambient operating temperature .......... +0/+25°C
Control pollution degree ................................... 2
Rated impulse voltage ................................. 4 kV
Enclosure rating .......................................... IP 21
Dimensions ...................... H/84, W/84, D/40 mm
Build-in depth .......................................... 20 mm
Display ........ 100x64 pixel STN - white backlight
EU Registered Design ........ 001101349-0001/2
The thermostat is maintenance free.
Español
El termostato de encendido y apagado es
electrónico y controla la temperatura por medio
de un sensor NTC ubicado en el exterior o en el
interior del termostato.
El termostato es para montaje a ras en un
receptáculo de pared. Se dispone de una placa
de base para el montaje mural externo.
PROGRAMA DE PRODUCTOS
FRTD 903
(MCD4-1999) Termostato horario y dos sen-
sores. Sensor de piso y sensor
incorporado de temperatura
ambiente.
ADVERTENCIA – Instrucciones de seguridad
importantes. Desconecte la fuente de alimen-
tación eléctrica antes de realizar cualquier
instalación o trabajo de mantenimiento en esta
unidad de control y componentes relaciona-
dos. Solamente una persona competente (por
ejemplo, un electricista cualificado) deberá
instalar esta unidad de control y componentes
relacionados. La instalación eléctrica debe reali-
zarse de acuerdo con las directivas estatutarias
apropiadas.
MONTAJE DEL SENSOR
El sensor de piso contiene un circuito de segu-
ridad de voltaje extra bajo (SELV, por su sigla en
inglés), que le permite ser colocado tan cerca
de la superficie del piso como sea necesario
sin tener que tomar en cuenta riesgo alguno de
electrocución si el cable del sensor se dañase.
Además, es preciso aislar con material termo-
encogible (p.ej. Shrink Flex) los dos alambres
que van del sensor a la caja de montaje.
Para impedir que los cables sueltos de la
instalación fija entren en contacto con el bloque
de terminales para el sensor de piso, será nece-
sario sujetar dichos cables con amarras.
Se recomienda colocar el cable y el sensor en
un tubo de instalación no conductivo incrustado
en el piso (fig. 3). Es preciso sellar el extremo
del tubo y colocarlo en la posición más alta
posible en la capa de hormigón. De manera
alternativa, el sensor se puede incrustar direc-
tamente en el piso. Es preciso que el cable del
sensor se pase a través de un tubo separado
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG FRTD 903 montage at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG FRTD 903 montage in the language / languages: English, German, Dutch, French, Polish, Swedish, Spanish as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info