462949
32
Zoom out
Zoom in
Previous page
1/72
Next page
Problem Possible cause Remedy
comes on
There is an error in the
appliance because a
cookware boils dry. The
overheating protection
for the cooking zones
and the Automatic
Switch Off operates.
Deactivate the appli-
ance. Remove the hot
cookware. After approxi-
mately 30 seconds, acti-
vate the cooking zone
again. If the cookware
was the problem, the er-
ror message goes out of
the display, but the re-
sidual heat indicator can
stay. Let the cookware
become sufficiently cool
and refer to “Cookware
for the induction cooking
zone” to see if your
cookware is compatible
with the appliance.
If you tried the above solutions and can-
not repair the problem, speak to your
dealer or the customer service. Give the
data from the rating plate, three digit
letter code for the glass ceramic (it is in
the corner of the glass surface) and an
error message that comes on.
Make sure, you operated the appliance
correctly. If not the servicing by a cus-
tomer service technician or dealer will
not be free of charge, also during the
warranty period. The instructions about
the customer service and conditions of
guarantee are in the guarantee booklet.
8. INSTALLATION INSTRUCTIONS
WARNING!
Refer to the Safety chapters.
Before the installation
Before the installation of the appliance,
record the information below from the
rating plate. The rating plate is on the
bottom of the appliance casing.
Model ...........................
PNC .............................
Serial number ....................
8.1 Built-in appliances
Only use the built-in appliances after
you assemble the appliance into cor-
rect built-in units and work surfaces
that align to the standards.
8.2 Connection cable
The appliance is supplied with the
connection cable.
Replace the damaged mains cable
with a special cable (type H05BB-F
Tmax 90°C; or higher). Speak to your
local Service Centre.
8.3 To attach the seal to the
rabbet
Clean the rabbet in the work surface.
Bond the seal stripe supplied on the
upper surface of the rabbet along the
edges of the cut out section.
Cut the seal stripe into four pieces in
relation to the length of the edges of
the rabbet.
For the four corners of the rabbet the
ends of the seal stripes must be cut in-
to mitres. Do not bond the ends over
one another.
32
www.aeg.com
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aeg-electrolux HK854400IB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aeg-electrolux HK854400IB in the language / languages: Dutch as an attachment in your email.

The manual is 13,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aeg-electrolux HK854400IB

Aeg-electrolux HK854400IB User Manual - Dutch - 16 pages

Aeg-electrolux HK854400IB User Manual - Italian - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info