English
42
CAUTION: INITIAL USE:
• Closethewatertankandplaceitbackinthebase.
• Connectthebasestationtoa230V~/50Hzsocketwith
earthing contact.
• Ifthehandleisstillinthecarryingposition,releasethe
lockasdescribedunder“FunctionoftheHandle”.
• UsetheselectorbuttonSET(11)tosetthetempera-
ture. Refer to the table above.
• Waituntilthesoleplatehasheatedup.Theoperating
temperature is reached as soon as the blue indicator
stops flashing and a beep sounds.
• Pressthesteamjetbutton(1)foratleast1/2minute.As
an alternative, you can pull back the lock (9) to lock the
steam jet button (10). This time is needed for the steam
to reach the iron. A slightly louder noise of the pump is
normal with this.
NOTE ON STEAM IRONING:
• Setting is not intended for steam ironing (see table).
• Theamountofsteamiselectronicallycontrolled.Itis
based on the ironing temperature.
• Theironingtemperatureiselectronicallycontrolled
during use. The device heats up if the blue indicator on
the display starts flashing slowly.
After use, press the selector button SET (11) repeatedly until
the red control lamp appears in the display. Disconnect the
mains plug from the socket.
Vertical Steam function (Vertical Steam)
This can be used to produce a jet of steam in a vertical
direction. This function can be used to remove creases from
hanging clothes or from curtains.
WARNING:
Never point the steam jet at other people. Danger of
burns.
Hang your laundry on a clothes hanger and move the iron to
approximately5-15cmaway.
How can I replenish the water during operation?
Refill with water before the tank is completely empty. A loud
noise of the pump during operation indicates that the water
level is too low.
• Placetheironontherest(5).
• PresstheselectorbuttonSET(11)
repeatedly until the red control lamp
appears in the display.
• Removethemainsplugfromthe
socket.
• Inordertoremovethetank,press
the RELEASE button below the water
tank. (Fig. C).
• Removethelimeltercartridge(Fig.D).
• Fillthetankuptothemaximummark
(Fig. E). Do not overfill!
• Reinsertthelimeltercartridgeandpush
the tank back into the base (Fig. F + G).
A "click" confirms that the water tank has
been set correctly.
• Youcannow
continue ironing.
NOTE:
The tank illumination lights once the mains plug has been
inserted into the outlet. If it does not light, the lime filter
cartridge or the water tank has not been set correctly.
Check both positions.
When you have finished
• PresstheselectorbuttonSET(11)repeatedlyuntilthered
control lamp appears in the display. Remove the mains
plug from the socket The light on the display goes out.
• Emptythewatertank.
• Allowthedevicetocooldownbeforeyouputitaway.
Anti-scale filter
Your steam iron station is fitted with an anti-scale filter. The
anti-scale filter cartridge becomes spent after filtering ap-
proximately18litresofwater,dependingonthehardness
of your water. It then loses its effectiveness and must be
replaced.
• Turnofftheappliance.
• Disconnectthemainsplugfromthemains.
• Removethewatertank.
• Removetheanti-scaleltercartridge.
• Fillthetankuptothemaximummark.Donotoverll!
• Insertanewanti-scaleltercartridge.
• Beforeturningontheappliance,waitafewminutesuntil
the new filter cartridge is saturated with water.
NOTE:
If you do not have a new anti-scale filter cartridge, you can
still iron with the used cartridge and distilled water.
Cleaning
WARNING:
• Alwaysremovethemainsleadbeforecleaning!
• Waituntilthemachinehascooleddowncompletely.
• Undernocircumstancesshouldyouimmersethe
device in water for cleaning purposes. Otherwise this
might result in an electric shock or fire.