463128
8
Zoom out
Zoom in
Previous page
1/11
Next page
14 15
.......................1510 W
.........................820 W
....................0-1500 min
-1
....................0-3000 min
-1
.........................890 min
-1
.......................1770 min
-1
.....................48000 min
-1
....................80-162 mm
......................32-90 mm
........................M18
...........................57 mm
..........................4,2 kg
...........................12 m/s
2
.........................100 dB (A)
......................... 111 dB (A)
ENGLISH ENGLISH
TECHNICAL DATA
Rated input ..............................................................................
Output ......................................................................................
No-load speed, 1st gear ..........................................................
No-load speed, 2nd gear .........................................................
Speed under load max., 1st gear ............................................
Speed under load max., 2nd gear ...........................................
Percussion rate max. ...............................................................
Drilling capacity, 1st gear .........................................................
Drilling capacity, 2nd gear .......................................................
Drive shank..............................................................................
Gear neck diameter .................................................................
Weight without cable ...............................................................
Typical weighted acceleration in the hand-arm area ...............
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) .......................................
Sound power level (K = 3 dB(A)) ............................................
Measured values determined according to EN 60 745.
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Contact with
a „live“ wire will also make exposed metal parts of the power
tool „live“ and shock the operator.
When working with large drill diameters, the auxiliary handle
must be fastened in a right angle with the main handle (see
illustrations, section “Twisting the handle”).
The built-in friction clutch only reacts to jerky locking, which
is why you should always use the additional handle.
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
The dust that arises when working with this tool can be
detrimental to health and therefore not reach the body. Wear
a suitable dust protection mask.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
When working in walls ceiling, or oor, take care to avoid
electric cables and gas or waterpipes.
SPECIFIED CONDITIONS OF USE
The diamond drill can be used to drill with diamond dry drill
bits. With drill chuck mounted the machine is suitable for
percussive drilling in rock and drilling holes in wood and
steel. The machine is not suitable for wet drilling in concrete.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 2004/108/EC
Rainer Kumpf
Manager Product Development
Winnenden, 2009-01-05
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
PROTECTION OF MOTOR IN CASE OF OVERLOAD
Motor protection device controlled by motor load. The
machine will slowly continue to run in order to cool the motor
down. After sufcient cooling machine can be restarted by
switching off and on again.
SOFT PERCUSSION
Depending on the material that is to be machined, soft
percussion may result in a sharp reduction in drilling time or
a longer tool life for the diamond segments.
ADVICE FOR OPERATION
To gain a better drill progress take out the centre bit after
having reached a depth of about 10-15 mm. Insert core
cutter into the existing groove and let machine run up
smoothly.
Bore-holes which don’t have to be applied exactly can be
drilled without a centre bit. For that purpose apply the core
cutter slantingly and put the machine slowly straight when a
depth of about 5 mm has been reached. (This is only
possible when using short core cutters!)
If drill cores should come loose, take core cutter from the
material and remove drill cores.
For best performance the diamond segments should be
“roughed-up” to expose the fragments of diamond: To
expose the diamond fragments rub surface of segments
with stone
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully
before starting the machine.
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together
with household waste material! In
observance of European Directive 2002/96/
EC on waste electrical and electronic
equipment and its implementation in
accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling
facility.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG DB 1500-2 XE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG DB 1500-2 XE in the language / languages: English, German as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info