Manual AEG BHG 1000W (page 13 of 48) (English, German, Dutch, French, Polish)

648325

Zoom out

Zoom in

1/48

Operation - Installation

4.6 Shutting down the system

» Stop the appliance by turning the rotary selector to

"OFF".

The ON indicator goes off.

» Pull the mains plug out of the wall socket.

5. Cleaning, care and

maintenance

Clean the surfaces when cold with a soft cloth and ordi-

nary cleaning products.

Note

Avoid abrasive or corrosive cleaning products.

6. Troubleshooting

6.1 Fault table

Fault Cause Remedy

The heated air

smells unpleasant.

This can be caused

by dust during com-

missioning.

The smell will dissipate

within a few minutes.

The appliance

does not heat up.

The MCB/fuse has

responded/blown.

Replace the fuse/reset the

MCB.

The appliance

heats continuously.

The appliance is sub-

ject to a continuous

draught.

Remedy the cause of the

draught.

The temperature set-

ting was changed.

Set the required room

temperature at the temper-

ature selector.

There is a fault with

the power supply.

Disconnect the appliance

from the power supply

for 10 minutes and then

switch it back on. If the

problem occurs regularly,

arrange for your power

supply utility to check the

power supply.

The 24 h automatic

function is not per-

formed.

There was a power

failure.

Set the 24 h automatic

function again.

The setting at the op-

erating mode selec-

tor was changed.

Set the 24 h automatic

function again.

The clocks have

changed to summer/

wintertime.

Set the 24 h automatic

function again.

The elements at

the very top and

bottom don't get as

warm as the rest of

the appliance.

The elements at the

top have not com-

pletely filled.

The heating medium ex-

pands when it gets warm.

It takes a little longer for

these elements to heat up.

Dirty marks appear

on the wall around

the appliance.

Dirty marks are

caused by contam-

inated air from the

interior (candles, cig-

arette smoke, poor

ventilation etc.).

Remedy the cause of any

air contamination.

If you cannot remedy the fault, notify your qualied con-

tractor. To facilitate and speed up your request, provide

the number from the type plate (000000-0000-000000).

The type plate is located underneath the appliance on

the right hand side.

INSTALLATION

7. Safety

Only a qualied contractor should carry out installation,

commissioning, maintenance and repair of the appliance.

7.1 General safety instructions

We guarantee trouble-free function and operational relia-

bility only if original accessories and spare parts intended

for the appliance are used.

7.2 Instructions, standards and regulations

Note

Observe all applicable national and regional regula-

tions and instructions.

8. Appliance description

8.1 Standard delivery

◦ Wall mounting bracket with xing materials

◦ 2 bathrobe hooks

The appliance is delivered fully wired.

9. Installation

9.1 Installation site

Material losses

Observe the minimum clearances in chapter "Spec-

ication".

Material losses

Fit the appliance to a vertical wall that is tempera-

ture-resistant to at least 80 °C.

Material losses

Never install the appliance directly below a wall

socket.

9.2 Wall mounting

Note

Observe the dimensions and minimum clearances

in chapter "Specication".

» Drill the holes and insert rawl plugs.

26_07_80_0058

1 Retainer screw

2 Wall sleeve

3 Lock screw

4 Retainer

5 Cap

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AEG BHG 1000W in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 9,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AEG BHG 1000W Manual

Product: