462626
46
Zoom out
Zoom in
Previous page
1/48
Next page
- 45 -
FAULT FINDING CHART
Suspected
problem
Probable cause Possible easy correction
Threads kink
together under the
fabric.
- Upper thread improper threading.
- Upper tension dial at O position.
- Re-thread. See page 14
- Increase upper thread tension. See page 18
Irregular stitches
- Incorrect needle size.
- Improper threading.
- Loose top thread tension
- Pulling fabric.
- Loose presser foot.
- Uneven wound bobbin
- Needle plate broken
- Choose correct size needle.
- Re-thread. See page 14
- Tighten top tension. See page 18
- Gently pull the fabric.
- Re-set presser foot.
- Re-wind bobbin. See page 10
11
- Change needle plate.
Breaking needle
- Wrong needle size for the fabric.
- The needle is curving.
- Pulling fabric.
- The needle clamp screw is loose.
- Pattern dial rotation when needle is in the fabric.
- Loose presser foot.
- Choose a needle to suit the thread and fabric.
- Re-set needle. See page 8
- Gently pull the fabric.
- Tighten the needle clamp screw.
- Bring needle to its highest position, before you choose a
pattern
- Re-set presser foot.
Bunching of thread
- Upper and lower thread not pulled back under
presser foot before sewing.
- Pull both threads under and back of presser foot, then
rotate the hand wheel with right hand.
Puckering
- Incorrect thread tension.
- Upper thread improper threading.
- Using two different sizes or types of thread.
- Bent or blunt needle.
- Loose presser foot
- Fabric too thin or too soft.
- Re-set thread tension. See page 18
- Re-thread. See page 14
- Use same size and type threads.
- Insert new needle.
- Re-set presser foot.
- Use underlay or vlies.
Skipping stitches
- Incorrect size needle.
- Bent or blunt needle.
- Incorrect setting of needle.
- Improper threading.
- Choose correct needle size for thread and fabric. See
page 20
- Insert new needle.
- Re-set needle. See page 8
- Re-thread. See page 14
Breaking upper
thread
- Starting to stitch too fast.
- Improper threading.
- Top thread tension too high.
- Incorrect setting of needle.
- Wrong needles and thread for the fabric.
- Set thread pool and the position indentation at left
side.
- Incorrect setting of bobbin case.
- Needle eye is sharp.
- Burrs on bobbin.
- Burrs on needle hole.
- Start to stitch at a medium speed.
- Re-thread. See page 14
- Adjust top thread tension. See page 18
- Re-set needle. See page 8
- Choose correct needle and thread to suit the fabric. See
page 20
- Adjust position of the indentation to right side.
See page 10
11
- Re-set bobbin case. See page 42
- Replace new needle.
- Sand or change bobbin case.
- Sand or change needle plate.
Breaking bobbin
thread
- Down thread improper threading.
- Down thread tension too high.
- Lint in bobbin or shuttle.
- Re-thread. See page 12
13
- Adjust thread tension. See page 19
- Clean bobbin case and shuttle. See page 42
Fabric not moving
- Stitch length in “O” position.
- Scraps in with feed-dog
- Sewing thread entangled
- Feed dog position down.
- Adjust stitch length.
- Clean feed dog. See page 38
- Pull back upper and bobbin thread under presser foot.
- Feed dog position up.
Machine jamming
knocking noise
- Thread caught in bobbin case.
- Remove and clean bobbin case. See page 42
Sewing machine
doesn’t operate
- The machine is not plugged in.
- Machine is not switched on.
- Plug in machine.
- Switch on machine
Down thread is
pulled above the
cloth.
- Top thread tension too high.
- Upper thread improper threading.
- Down thread improper threading.
- Adjust top thread tension. See page 18
- Re-thread. See page 14
- Re-thread. See page 12
13
When it is a vacant
screen
- LCD gets shut down - Turn off power
- Re-turn on power, re-setting all conditions as previous
ones
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG 681 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG 681 in the language / languages: English, German as an attachment in your email.

The manual is 3,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info