462615
27
Zoom out
Zoom in
Previous page
1/40
Next page
- 26 -
Während des Nähens zeigt die LED “ (Garn verdrillt)” an und
stoppt. Drehen Sie das Handrad, um das Problem zu lösen.
During sewing, LED show out ” and stop. Turn hand wheel to solve
torque problem.
MIT DEM NÄHEN BEGINNEN (VORBEREITUNG)
Nachdem Sie sich mit der Bedienung der Nähmaschine vertraut gemacht haben, können Sie mit dem Nähen beginnen. Beachten Sie bitte vor
dem Nähen die folgenden Punkte, um problemlos zu nähen.
1. Überprüfen Sie, ob die Nadel gerade, unbeschädigt und richtig eingesetzt ist.
2. Stellen Sie die Nadel vor Beginn und nach Ende des Nähens ganz nach oben.
3. Ziehen Sie vor dem Nähen vorsichtig den Ober- und Unterfaden ca. 10 cm heraus und durch den Nähfuß hindurch.
4. Probieren Sie zuerst an einem Reststück die geeignete Stichlänge und Fadenspannung aus.
5. Legen Sie den Stoff unter den Nähfuß.
6. Oder verwenden Sie den Fußanlasser. Drücken Sie ihn zum Nähen langsam nach unten.
7. Der Beginn und das Ende jeder Naht muss auf einem kurzen Stück rückwärts genäht werden, um das Aufgehen der Naht zu verhindern.
(Das Rückwärtsnähen ist aber nur für gerade Stiche geeignet.)
8. Führen Sie den Stoff mit der Hand vorsichtig vor der Nadel. Halten Sie den Stoff nicht fest, da dies den Transport durch die Maschine
beeinträchtigen kann.
9. Drehen Sie das Handrad beim Drehen immer nach vorne (gegen den Uhrzeigersinn).
10. Stellen Sie die Nadel nach dem Beenden des Nähens und vor der Entnahme des Stoffes ganz nach oben, so dass die Nadelspitze den
Stoff nicht mehr berührt, um ein Verbiegen oder Abbrechen der Nadel zu vermeiden. Ziehen Sie den Stoff dann nach hinten heraus.
START SEWING (PREPARATION)
After being familiar with the sewing machine you may start sewing. Before you start sewing you should pay attention to the following points, so
sewing will be smoothly.
1. Inspect the needle for correct installation.
2. Raise the needle to the top before sewing and after you complete sewing.
3. Before sewing, first gently pull upper and down threads about approx. 10 centimeters
(4 inches) and pass them through under the presser foot.
4. Use a piece of cloth, to decide the suitable stitch length and the thread tension.
5. Put the cloth under the presser foot.
6. Or use foot controller. Slowly press the foot controller to sew.
7. With the reverse stitch you ensure that the seam does not unstitch at the end and the beginning
8. Gently hold the fabric in front of the needle to deliver the cloth, do not hold onto the cloth, as the machine will not be able to deliver the
cloth by itself.
9. When you turn the hand wheel, turn it to the front (counter- clockwise).
10. To avoid that the sewing machine needle bents or breaks after sewing, you must rise the needle to the top before you take the cloth away
backwards.
FEHLERBEHEBUNG / ERROR CORRECTION
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG 11679 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG 11679 in the language / languages: English, German as an attachment in your email.

The manual is 3,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info