684408
10
Zoom out
Zoom in
Previous page
1/37
Next page
- 9 -
5 cm Faden
5 cm thread
Richtig
Correct
AUFSPULEN / WINDING THE BOBBIN
Schieben Sie den Spuler in Pfeilrichtung, und wenn Sie mit
dem Spulen fertig sind wieder in die Ausgangsposition zurück.
Push bobbin winder spindle in direction of the arrow. When
bobbin winding is completed, return spindle to its original
position.
Wenn das Aufspulen nicht gleichmäßig erfolgt, lösen Sie die
Schraube der Vorspulerspannung und stellen Sie diese bei
Bedarf nach oben oder unten, bis gleichmäßig aufgespult wird.
When bobbin winding is uneven, release the screw of the upper
thread guide and adjust up or down until bobbin the winding is
balanced.
Spuler
Spindle
1. Drücken Sie am Handrad zum Spulen den Kupplungsknopf
Richtung Spulensymbol, um die Bewegung der Nadel beim
Spulvorgang zu stoppen und führen Sie den Faden von der
Garnrolle durch die Aufspulscheibe.
2. Führen Sie das Fadenende ca. 5cm von innen durch die Öff-
nung in der Spule und setzen Sie die Spule auf den Spuler,
dann drücken Sie den Spuler nach rechts.
3. Halten Sie das Fadenende fest und drücken Sie leicht auf
den Fußanlasser. Stoppen Sie den Spulvorgang, nachdem
der Faden sich einige Male um die Spule gewickelt hat.
Schneiden Sie das überstehende Fadenende dicht an der
Spule ab und spulen Sie fertig.
4. Nach dem Aufspulen drücken Sie den Kupplungsknopf
wieder Richtung Nadelsymbol, um den Kontakt
wieder herzustellen.
1. For bobbin winding push the knob in the handwheel towards
the bobbin symbol, in order to stop the needle movement
while winding and lead the thread from the spool through the
bobbin winder tension disc.
2. Now pull the end of the thread about 5 cm through the hole in
the bobbin from the inside to the top. Place the bobbin on the
bobbin winder and push the bobbin winder to the right.
3. Hold the end of the thread and step on the foot controller. As
soon as the bobbin is wound with the thread a few times
let the end of the thread go. Cut the excess thread close
to the bobbin and wind the bobbin.
4. When winding is finished, push the knob in direction of needle
symbol to get contact.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG 112704 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG 112704 in the language / languages: English, German as an attachment in your email.

The manual is 3,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info