521961

AdvanSea WIND-a S400 Manual

8
Zoom out
Zoom in
Previous page
1/72
Next page
S400 Wind masthead installation manual 8
2.1. Mounting the wind vane-gauge cable
It is recommended to mount the wind vane-gauge cable before mounting the boat's
mast.
The wind vane-gauge sensor bracket, at one end of the cable, must be installed on the
masthead as follows:
• The base of the bracket must be placed horizontally.
• The arm of the wind vane-gauge sensor must be directed towards the front,
parallel to the boat's axis.
• Fix the bracket to the masthead using the 2 Ø 4 mm screws.
• Drill a hole of Ø 6 mm through the masthead, near the bracket, so as to
insert the cable inside the mast.
• Drill a hole of Ø 6 mm on the lower part of the mast for exiting the cable.
• Position a watertight junction box (Option on www.advansea.com
) close to
the mast base, in order to connect the wind vane-gauge sensor cable, and
facilitate future dismasting.
• Calculate the required length of cable between the sensor bracket and the
junction box. Add a few centimetres to attach the cable in the junction box.
• Cut the sensor cable to the measured length and retain the part equipped
with the overmoulded connector.
• Insert the sensor cable through the hole in the masthead, and slide it down
the groove for masthead cables, exiting through the hole at the base of the
mast. Fix the cable to the masthead using a cable grip and seal the holes
drilled in the mast using silicone sealant.
• Connect the part of the sensor cable fitted with the overmoulded connector
to the WIND display cable, and install this cable in the junction box at the
base of the mast (option on www.advansea.com).
• Insert the 2 ends of the sensor cable in the junction box at the base of the
mast (option on www.advansea.com
), strip the wires and connect the two
cables respecting the wire colours.
• Close the junction box at the base of the mast (option sur
www.advansea.com
), ensuring it is watertight.
• If you have decided not to install the junction box at the base of the mast,
solder the wire together respecting the colours and ensuring they are
insulated from each other. Also ensure that this assembly is watertight by
means of systems such as sealed heat-retractable sheaths. AdvanSea shall
not be held liable under the warranty for improper connections in this
location without the use of the junction box at the base of the mast (option
at www.advansea.com
)
2. Installation
www.busse-yachtshop.de | info@busse-yachtshop.de
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AdvanSea WIND-a S400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AdvanSea WIND-a S400 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AdvanSea WIND-a S400

AdvanSea WIND-a S400 User Manual - German - 22 pages

AdvanSea WIND-a S400 User Manual - All languages - 221 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info