632362

Aduro Asgard 2 Manual

21
Zoom out
Zoom in
Previous page
1/34
Next page
_______________________________________________________________________________________________________________________________
- 21 -
In order to reduce the risk of ash falling from the stove when the door is opened to add more fuel, it is a good idea
to open the primary air intake/damper for approx. 1 minute before the door is opened. This increases the draught
through the stove and reduces the risk that ash will drop on the floor.
Please note: if you overload the wood burning stove and burn more than approx. 2.5 kg wood/hour, there is a risk
that the lacquered surface of the stove will become discoloured and eventually fall off. The stove can be resurfaced,
but this is not covered by the manufacturer’s guarantee. In the same way, any other damage to the stove caused by
overloading will not be covered by the guarantee.
3.8 Ventilation/fresh air supply
In order for the wood burning stove to function at optimum efficiency, air is needed for the combustion process.
There must be sufficient fresh air coming into the room containing the wood burning stove. In very well-insulated
houses, or houses with powerful cooker hoods and/or air conditioning systems, a vacuum can be created around
the stove, leading to smoke leakage and poor combustion. In these circumstances, it might be necessary to open a
window to provide air for combustion and to equalize the vacuum. Alternatively, you could fit an air vent in the room
containing the wood burning stove. The amount of air needed for combustion is 25 m
3
/h.
4.0 The chimney
Data for chimney calculation:
Wood
Flue temperature at [20 C]
367
Chimney draught at testing power
[mbar]/[Pa]
0.12/12
Flue gas mass flow [g/s]
4,0
The optimum combustion is achieved at a constant chimney draught of 0.10 to 0.14 mbar measured in the flue pipe
above the stove. There are many factors that affect the chimney draught, including the outside temperature, wind
strength and surrounding buildings. If it is impossible to establish a sufficiently natural chimney draught, the chimney
can be fitted with a smoke extractor. If the chimney draught is too strong, a damper can be fitted to regulate the
chimney draught. Contact your local chimney sweep for more advice.
There are no requirements with respect to specific chimney heights, but a chimney must be tall enough to provide a
good draught – above 12 Pa. If the recommended chimney draught is not achieved, there may be problems with
smoke out of the door by firing.
4.1 Inadequate draught in the chimney
If the chimney is too short, leaks or is inadequately insulated, there may be problems with the chimney draught (let
the chimney sweep assess this). The draught should be approx. 0.10–0.14 mbar in order to provide satisfactory
combustion and prevent smoke leakage.
If the chimney sweep judges the draught to be satisfactory, but you still have problems lighting a fire, try extending
the fire lighting phase/using more thin pieces of kindling, so that the chimney gets thoroughly warm. The chimney
will not draw at optimum effect until it is warm. The fire lighting phase can be prolonged by using a lot of kindling
and 1-2 firelighters. When a layer of embers has been formed, add 2–3 dry logs.
5.0 Maintaining and cleaning your wood burning stove
Gaskets
With time, the gaskets will wear, and, in order to avoid wild combustion, they must be replaced as required.
Glass
If the wood you burn is too moist, you will get soot stains on the glass pane. They can be easily removed using a
damp cloth that you dip in cold ash and rub on the sooty glass. Special cleaning agents are also available to remove
soot from glass, i.e. the Aduro Easy Clean pad.
Combustion chamber
The yellow tiles in the combustion chamber eventually wear out and they should be replaced when the cracks are
more that 0.5 cm. The durability of the tiles will depend on how often and how intensively the stove is used. You can
change the tiles yourself. They are available as a ready-to-use set. You can also buy one-piece tiles that you can
cut to the size of the worn plates yourself. Please visit www.aduroshop.com.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aduro Asgard 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aduro Asgard 2 in the language / languages: English, German, Danish, French, Swedish as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info