Manual Aduro 9-1 (page 22 of 43) (English, German, Danish, French, Swedish)

632352

Zoom out

Zoom in

1/43

_______________________________________________________________________________________________________________________________

Please note: that the Aduro 9-1 must be installed on a floor with the adequate load-bearing capacity. If the existing

construction does not meet this requirement, appropriate adaptation measures must be taken (e.g. a load-

distributing plate).

If the wood burning stove is to be placed close to flammable material, such as a wooden floor or carpet, it must be

placed on a non-flammable base. The floor plate should extend for at least 30 cm in front of the wood burning

stove, and 15 cm on each side.

2.2 Pipe connection

Aduro 9-1 leaves the factory with the flue outlet mounted on the top. If you require the flue outlet on the back,

remove the round circle from the rear cover at the upper rear of the stove and then exchange the exhaust

connector (located on the top outlet above the stove) with the cover plate (that covers the rear outlet). The inner

heat shield (which is attached to the back plate) has to be removed, since this should not be used when the rear

outlet is chosen. The top outlet is finished with the plate that lies in the ash drawer. A flue pipe with an internal

diameter of 150 mm should be used for Aduro stoves.

2.3 Connection to a brick chimney

If the stove is being connected to a brick chimney, a curved flue pipe should be used via the top outlet. After

measurement, a hole is made in the chimney in which the pipe sleeve is placed and fireplace mortar is used to seal

it in place. The stove is placed in position and the flue pipe is put in place. A thin gasket is placed between the flue

pipe and the pipe sleeve to seal the joints. The flue pipe should protrude 5–10 cm into the pipe sleeve, but must not

block the opening in the chimney (see the illustration below).

The wood burning stove can be connected to a chimney to which other heat sources are connected.

3.0 Lighting a fire in the wood burning stove

3.1 Important safety information

 The wood burning stove will become warm during use and therefore it should be treated with all necessary

caution.

 Never keep easily combustible fluids such as petrol in the vicinity of the wood burning stove – and never

use easily combustible fluids to light the fire in the wood burning stove.

 Never empty the ash drawer when the wood burning stove is warm. Embers may still be found in the ash

drawer for up to 24 hours after the fire has gone out. Please wait to empty the ash drawer until you are

sure that there are no embers in the ash.

 The door should be kept closed while the wood burning stove is in use. While lighting the fire, the door can

stand ajar for the first few minutes.

 In the event of a chimney fire: Close all the dampers on the wood burning stove and call the fire-fighting

service.

3.2 Recommended fuels?

Wood and woodbriquettes. We recommend the use of split hardwood that has been stored outdoors under

cover for at least 1 year. Wood that has been stored indoors has a tendency to become too dry and will burn

too quickly. The wood should preferably be felled in the winter, when a lot of the moisture in the wood will have

been drawn down into the roots. In order to achieve optimum combustion, the wood’s moisture level should not

exceed 18 %, which roughly corresponds to storing the wood under cover outdoors for one year. The moisture

level of the wood can be measured using a moisture meter or by applying washing up liquid to one end of the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aduro 9-1 in the language / languages: English, German, Danish, French, Swedish as an attachment in your email.

The manual is 0,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aduro 9-1

Aduro 9-1 User Manual - Dutch - 10 pages

Aduro 9-1 User Manual - Italian, Spanish - 87 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aduro 9-1 Manual

Product: