429063
4
Zoom out
Zoom in
Previous page
1/14
Next page
4 Issue 1, May 2004 61180019L1-5A
The recommended ways to mount the chassis are as
follows:
Flush-mount: To flush-mount a Total Access 1500
19-Inch Chassis in the rack, use a #2 phillips-head
screwdriver and attach the mounting brackets (see
Figure 2) with the flanges containing the slotted
rack-mounting holes facing the front of the Total
Access 1500 19-Inch Chassis. The mounting brack-
ets should be attached using the set of mounting
bracket holes closest to the rear of the Total Access
1500 19-Inch Chassis.
Figure 2. Flush-Mount Bracket Orientation
Mid-mount: To mid-mount a Total Access 1500 19-
Inch Chassis in the rack, use a #2 phillips-head
screwdriver and attach the mounting brackets (see
Figure 3) with the flanges containing the slotted
rack-mounting holes facing the rear of the Total
Access 1500 19-Inch Chassis. The mounting brack-
ets should be attached using the set of mounting
bracket holes closest to the front of the Total Access
1500 19-Inch Chassis.
Figure 3. Mid-Mount Bracket Orientation
Installing the Chassis
After attaching the mounting brackets to the Total
Access 1500 19-Inch Chassis sides, use the appropriate
screws for the CO rack type and mount the chassis in the
rack as follows:
1. Flush-mount: For flush-mount systems, the Total
Access 1500 19-Inch Chassis must be mounted
from the rear of the rack, with mounting bracket
flanges facing rearward.
2. Mid-mount: For mid-mount systems, the Total
Access 1500 19-Inch Chassis must be mounted
from the front of the rack, with the mounting
bracket flanges facing forward.
NOTE
Other orientations will require either mounting
from the front or rear, and depend on the rack
type installed in the CO and the standard
operating procedures established by the CO.
Once the orientation of the chassis has been determined,
use the four appropriate screws for the CO rack and an
appropriate screwdriver and secure the Total Access
1500 19-Inch Chassis in place on the rack.
Connections
Interconnections between the common modules and
channel units are accomplished through the backplane
PCB. All external connections to the Total Access 1500
19-Inch Chassis are through connectors and wire-wrap
headers located on the backplane.
NOTE
When connecting power and ground wiring, be
sure to follow all local, national, and company
codes.
CAUTION
Per GR-1089-CORE October 2002, section 9,
this system is designed and intended only for
installation in a DC-C (common) Bonding and
Grounding System. It is not intended or
designed for installation in a DC-I (isolated)
Bonding and Grounding system.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adtran total access 1500 quad line interface unit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adtran total access 1500 quad line interface unit in the language / languages: English as an attachment in your email.

The manual is 4,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info