Manual Adler CR 7745 (page 8 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish)

802401

Zoom out

Zoom in

1/120

Control panel (1) / Remote control (9) buttons description:

A. Standby mode button B. Heating level button C. Timer button

D. Temperature decrease button E. Temperature increase button F. Oscillation button

Display panel (2) icons description:

A1. Cool air airflow icon B1. Warm air heating icon

B1. + B2. Hot air heating icons C1. Timer icon

F1. Oscillation function icon G. Temperature icon

USAGE

1. Ensure the power switch (8) is off. Insert the plug into a suitable power outlet and turn the power supply on by pressing to position I the

power switch (8) located at the back of the device. The device is in standby mode.

2. Press button (A) on the control panel (1) that will respond to your touch, and the LED display (2) shows the room temperature (G). The

cool air is flowing and fan icon (A1) is shown too.

3. Press button (B) to control temperature of heating:

- Once, to get warm airflow, the icon (B1) will be illuminated up.

- Twice, to get hot airflow, both of sun (B1 and B2) will be illuminated up.

- Third time, to come back to cool airflow.

4. Press button (C) repeatedly to set a period after which the device will turn itself off. Time range from 0 to 12 hours. When timer function

is active the icon (C1) is illuminated up on the display panel (2).

5. Press button (D) or (E) to control required room temperature. Temperature setting from 10 to 35 degree of Celsius. Press button (E) to

increase the desired temperature and button (D) to decrease the desired temperature. The temperature icon (G) indicates the current room

temperature, e.g. 21 degrees Celsius. After selecting the desired temperature in the room, e.g. 25 degrees Celsius, the display will flash

four times remembering the target temperature of 25 degrees Celsius, and then return to showing the current ambient temperature, i.e. 21

degrees Celsius, which will increase to 25 degrees over time.

The device control room temperature automatically according to below principle:

- when the room temperature lower 4 degree of Celsius than the settled temperature on the device, it's hot air heating power,

- when the room temperature lower 2 degree of Celsius than the settled temperature on the device, it's warm air heating power,

- if room temperature reach the setting temperature, the heating stop, the fan is permanently flowing cool air until the room temperature

lower than the setting temperature by 2 degree of Celsius. If it occurs the device automatically return to warm air heating power,

- if room temperature lower 4 degree of Celsius than the settled temperature on the device, it's automatically return to hot air heating.

6.Press button (F) to active oscillation function, the icon (F1) will be illuminated up at display panel (2), the device will swing the left side

and the right side in range of angle 60 degree. Press it again to cancel the oscillation function.

7. Press button (A) again, the icon (A1) is blinking the device will working 30-60 seconds with cool airflow to cool down inside components

before shutting down to standby. Such design protects the device lifetime.

8. Operation by remote control (9) is same as operation by button pressing on the control panel (1).

BATTERY ECHANGE PROCEDURE

Follow the instructions of use and the recycle rules given on the battery packaging. The procedure of battery replacement is described

below – look at figure 3.

1. Open the battery compartment by sliding the cover down.

2. Insert the battery into the compartment. The remote control requires 1 CR2025 3V lithium battery.

3. Close the battery compartment.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Adler CR 7745 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 2.65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Adler CR 7745 Manual

Product: