732320

Adler AD 7963 Manual

6
Zoom out
Zoom in
Previous page
1/80
Next page
6
DESCRIPTION OF THE DEVICE: ULTRASONIC HUMIDIFIER (picture A)
A7. Water descaling filter A8. Sponge in fragrance box
LCD CONTROL PANEL (figure B)
B5. SLEEP button B6. Timer indicator 1-12 hours
37. Do not lift the water tank by the water mist outlet.
38. It is prohibited to insert metal chips, wire, needles and other foreign objects into the
product or into the housing gaps, otherwise it may cause electric shock or malfunction.
The device is designed to work in rooms with a temperature of 5-40 ° C and a relative
humidity of 80%.
B1. Power button B2. Mist SPEED button
B7. Water shortage indicator B8. HUMIDITY value indicator %
USING (picture C)
1.After transportation in low temperatures, leave the appliance in the room for 2 hours to acclimate before using. Do not use the device
without water.
B3. TIMER button B4. HUMIDITY button %
B9. MIST intensity indicator 1/2/3 drops (weak / medium / strong)
B10. Night Light button B11. Night Light indicator
A5. Water tank cover A6. Remote control
A1. Water mist outlet A2. Water tank
B12. SLEEP function indicator B13. HUMIDITY function indicator
A3. Base A4. LCD Control panel
Note: When the device is on, it shows the current humidity level in room. When the room reaches the humidity % you set, the device will
stop working automatically. When the humidity % decrease and becomes less than the preset humidity %, the device will start working
again. If you don't set the room humidity, the device will keep running until the water is over. The humidifier mainly shows the humidity
near the machine.
10.Touch the power button (B1), the LCD screen will light up and the device will start working. The display will show the humidity % near
the machine and the function you set. The mist will start come out after several seconds.
2.Make sure the device is unplugged.
7.Slide out of the fragrance box from the base (A3) and put aroma oil on the aroma sponge (A8) if you desire, 3-5 drops of oil on the
sponge should be enough. Aroma oil is not included in set. Do not add any aromatic substances into the water tank A2 (powder, liquids
oil, etc.). Aromatic oil should be poured only on the sponge (A8) located in the fragrance box in the bottom of unit from back side.
8.Remove plastic insert from the remote control (A6) to active the battery. The remote control (A6) operates the device in the same way
as the control panel buttons on the device housing (picture B).
11. Press the SPEED (B2) button one, two or three times to activate continuous mist output at low or medium or strong level.
16. Press the power button ON/OFF (B1) again so that the device stops working and goes into standby mode. Unplug the power plug.
If there is not enough water in the water tank, the device will beep and the display will show water shortage indication (B7) and have
beep indication voice. The delayed switch-off and constant humidity setting is canceled. The device will stop working after some
seconds. Unplug the device and refill the water tank.
4.Top up the water tank (A2) only when the machine is switched off from the power supply. Do not pour water into the tank above the
maximum level – look at picture C . Do not pour water into the housing gaps and into the mist outlet pipe shown in Picture C.
14. Press the LIGHT button (B10) to turn on and turn off the night light. The night light will change colors.
Note: If moisture collects around the appliance, this is not a defect. It may be an indication that the humidity level is set too high. Reduce
the mist output or reduce the required value of humidity %. It is normal to hear dripping sound when the mist output is at high level.
15. Press the SLEEP button (B5) to set the LCD display illumination ON/OFF.
5.Place the filled water tank on the base (A3) in correct position, make sure the filter (A7) is properly placed. Wait a 1-2 minutes before
starting the device.
13.Press the button (B4) to set required humidity from 45% to 90%.
3.Remove the water tank cover (A5). Remove the water tank (A2) from the base of the device (A3)
9.Connect the device to the power supply. The device will emit a single sound and will wait for setting the operating mode.
12.Press the TIMER button (B3) to set the delayed switch-off of device, adjust required time in range: 1-12 hours. The device will switch
off after required time of continuous operation.
6.Close the water tank cover (A5).
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 7963 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 7963 in the language / languages: All languages as an attachment in your email.

The manual is 4,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info