800026

Adler AD 7749 Manual

6
Zoom out
Zoom in
Previous page
1/76
Next page
6
temperature controlling device or time switch.
20. Flammable materials, for example furniture, bedclothes, paper, clothes, curtains should
be kept at least one meter from the device.
21. Do not cover the device or put any objects on it while it is operating. Do not use the
device to dry clothes.
22.The heating surfaces can heat to a temperature of 60 °C or higher. The device should be
in a place that children and animals do not have access to.
23.The device is not intended to be installed or used in vehicles.
24. Some parts inside the device can be hot or cause sparking. Do not use the device in
places, where gasoline, paints or other flammable materials are used or stored.
25. The device must not be located immediately below a socket-outlet.
Before first use
The device should be used in wall sockets in a vertical position only, and not horizontally (lying).
WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless
constant supervision is provided.
Device description:
1. Power switch 2. Fan speed butto 3.A. Temperature DOWN button
3.B. Temperature UP button 4. Timer button 5. Air inlet
6. Plug 7. Air outlet 8. Digital display
Instruction Manual
1. Plug device into 220-240V power supply outlet.
2. Press the power switch (1) on side of the unit to position “I” to turn on the device. Default device setting is: temperature 25 degree of
Celsius and high fan speed (HH).
3. Select your desired temperature by pressing “+” button (3.B.) to raise temperature or “-“ button (3.A.) to lower the temperature between
15-35 degree of Celsius on digital display. Pressing the button once changes one degree Celsius.
4. Select your desired fan speed by pressing button (2) to choice between high (HH) or low (LL) fan speed.
At “LL” low fan speed the operation is like below:
- If your desired temperature shown at digital display (8) is higher than present room temperature the heating element will heat the air at low
speed of fan,
- If you desired temperature shown at digital display (8) become lower than present room temperature the heating element stops air
heating, but fan will continue to blow the air at low speed.
At “HH” high fan speed the operation is like below:
- If your desired temperature shown at digital display (8) is higher than present room temperature the heating element will heat the air at
high speed of fan,
- If you desired temperature shown at digital display (8) become lower than present room temperature the heating element stops air
heating, but fan will continue to blow the air at high speed.
5.To change temperature unit from Celsius to Fahrenheit scale button (2) for a few seconds. To come back from Fahrenheit to Celsius press
button (2) for a few seconds again.
6. To stop operation, turn the power switch (1) to “0” position and unplug the device from power outlet.
NOTE: If you do not set the timer, the digital display (8) always shows default setting temperature (25℃) or desired temperature set up by
you.
Setting the timer
The device has a built-in timer that will automatically turn the device off after a set amount of time.
1. While the unit is plugged in and turned on, press the Timer button (4) to active the function of timer.
2. Press Timer button (4) again to set desired number of hours. You can choose between 1-12 hours.
3. Once desired number of hours have been chosen, the display will flashing twice. The device will automatically turn off after desired
amount of time passed.
4. To cancel timer settings, turn the device off or press the timer button until the display shows “00”.
The digital display shows the temperature set by the user, and if additionally the timer was previously set, the display shows the desired
temperature and the set time alternately.
OVERHEAT PROTECTION SYSTEM
The device is provided with a safety system that automatically cuts the power to the heater in the event of overheating. If this event occurs,
switch the device off, remove the plug from the power outlet and wait until the device has cooled down (after about 10 minutes).
CLEANING AND MAINTENANCE
Make sure the device is not hot. Remove the plug from the socket before cleaning. Keep the inlet and outlet openings clean. Do not allow
dust to settle on them. Use a dry or slightly damp cloth to clean housing. Do not immerse the device in water. Store the device in a cool, dry
place until next use.
TECHNICAL DATA
Voltage: 220-240V~ 50Hz
Power: 400W
Max power: 1500W To protect your environment: please separate carton boxes and plastic bags and dispose them in
corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due
to hazarsous components, which may effect the environment. Do not dispose this appliance in the
common waste bin.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 7749 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 7749 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info