800011

Adler AD 7333 Manual

4
Zoom out
Zoom in
Previous page
1/60
Next page
4
injury or damage to the device.
Montage
1. First assemble the base by aligning the assembly poles with the corresponding holes, and insert the poles into the holes X. Look at
picture A1.
2. Align the assembled base with the two holes (Y) with the tab on the fan body (V). See picture A2.
3. Once connected, screw the base to the body using screws (Z) supplied. And put the power cord into the slot of the base.
4. Stand the fan upright.
Product Description: Tower Fan Ad7333 - picture B
1. LCD panel 2. Air outlet
3. Front housing 4. Base
5. Handle 6. Air inlet
7. Back housing 8. Remote control
LCD panel and remote control description - picture C
A. Power button B. Fan speed button
C. Oscillation button D. Timer button
E. LCD panel’s light up button
Operation
Place the device on a flat and even surface. Plug in the device. The device will bleep and display the current room temperature to
indicate the device is working well.
Firstly, press the button (A) to start operation. Once activated, you can then select your desired function using the LCD Panel (1) or
Remote Control (8) as described below:
1. By pressing the button (A) turn on the device, default setting is in middle fan speed. Press the button (A) it again, the device is in
standby.
2. Press the button (B) to select middle, high or low fan speed. Default setting is on middle speed when start.
3. Press the button (C) to oscillate / swing the air flow evenly the left and in the right direction. Proper control lamp will light on the LCD
panel (1). Press the button (C) again to cancel air oscillation function.
4. Press the (D) button to set the timer from 0 to 12 hours, each press is 1 hour increments when the unit turns off automatically.
5. Control panel light button (E): After continuous operation for 10 minutes, if no any operate by user, the display (1) stops to light up
automatically. To light up the display (1) again, press any button.
Temperature display: After setting all desired function, LED display (1) will automatically display room temperature again.
Remote control (8) operation is same as manual operation of buttons on LED panel (1). To use the device with the remote control (8)
supplied, pull the installing film. In order to remove the battery, simply squeeze the small tab and pull – look at picture D. Insert 1 x
CR2025 (3V) lithium battery into the small crevice. IMPORTANT: The + symbol on the battery inserted should be facing upwards. Firmly
close the battery compartment to begin using the Remote Control (8).
CLEANING AND MAINTENANCE
CAUTION: Do not allow the fan's motor part or any buttons to get wet.
1. Before cleaning remove the plug from the electrical socket.
2. To clean housing gently wipe it with a damp cloth, without detergents. Wipe dry.
3. Store the fan in a dry place.
Technical Data:
Power: 60 W Maximum Power: 120W Voltage: 220-240V ~ 50Hz Noice: ≤ 63dB (A)
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
DEUTSCH
ALLGEMEINE SICHERHEITSVORSCHRIFTEN LESEN SIE AUFMERKSAM WICHTIGE
ANWEISUNGEN BEZÜGLICH DER SICHERHEIT DER BENUTZUNG BEWAHREN SIE
DIESE FÜR DIE ZUKUNFT AUF
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
geändert.
1.Vor dem ersten Gebrauch, die Bedienungsanleitung lesen und die dort angegebenen
Hinweise beachten. Der Produzent trägt keine Verantwortung für Schäden, die aufgrund
von bestimmungswidriger Nutzung oder unsachgemäßer Bedienung entstanden sind.
2.Das Gerät ist nur für den Hausgebrauch verwendet. Verwenden Sie es nicht für andere
Zwecke als den bestimmungsgemäßen Gebrauch.
3.Das Gerät ausschließlich an die Steckdose 220-240 V ~ 50 Hz anschließen. Es darf
nicht zu anderen, bestimmungswidrigen Zwecken benutzt werden. Wegen
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 7333 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 7333 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 4.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info