737920

Adler Ad 4808 Manual

4
Zoom out
Zoom in
Previous page
1/64
Next page
bigger parts into pieces.
21.Do not cover the ventilation holes in the housing while the machine is on.
22.Do not immerse the drive assembly in water, don't clean it under running water.
23.Do not clean the equipment while mounted on the machine's drive assembly.
24.Don't use aggressive detergents to clean the housing, as it may remove the
informational graphic symbols such as: scale, signs, safety marks,Etc.
25.Do not wash the metal parts in dishwashers. Aggressive cleaning agents used in
dishwashers cause the metal parts to turn black. Handwash the metal parts using
traditional washing-up liquid. Use soft brush.
26.Do not grind dry poppy seed. The poppy seed needs to be steamed and soaked before
grinding.
DEVICE DESCRIPTION
1. machine body 2. power switch (I) / reverse button
3. grinding chamber 4. tray
5. pusher 6. grinding chamber lock button
7. drive assembly head 8. screw
9. screw coupler 10. knife
11. 3 hole plates (3 mm, 5 mm, 7 mm) 12. nut
13. sausage/butcher attachment
PREPARING MEAT GRINDER FOR OPERATION
Grinding assembly (fig 3)
In order to assembly the grounding chamber (3), insert the elements in following order:
- Screw (8)
- Knife (10) onto screw pin, with blades facing the hole plate
- Then one of hole plates (11), with the chamber protrusion matching the groove on the outside edge of the plate
- Gently tighten the assembly with the nut (12)
PREPARATION OF GRINDER
1.Place the machine body on even, hard surface, so that the ventilation holes are not covered, and close to power outlet
2.Before use wash the grinding chamber with all elements, tray (4) and pusher.
3.Check if the grinding chamber is complete. If not, assembly the chamber using all elements, according to figure 3.
4.Mount the assembled grinding part in the drive, so that the coupler (9) fits the drive head (7). Press in the grinding part, and rotate
counter clockwise until vertical. Audible click is heard when the assembly is mounted correctly. Tighten nut (12) on the grinding chamber
(3).
5.Mount the tray (4) on top of the grinding chamber.
DEVICE OPERATION
1.Turn the device on by pressing the upper part of button (2) – forward.
2.Put the previously prepared products to be ground into grinding chamber, shoving them with the pusher (5).
3.If needed, you can turn on reverse rotations by pushing the lower part of button (2).
SAUSAGE ATTACHMENT
The attachment is used for in-house sausage production.
1.Assemble the set according to figure 4.
2.Soak the previously prepared intestine casings (called rounds) in warm water for about 30 minutes before stuffing.
3.Put the wet rounds on the outside of sausage attachment, gently slide down during stuffing, and wind for preferred length.
CLEANING AND MAINTENANCE
1.Don't immerse grinder in water or other liquids.
2.Do not clean the casing using strong detergents in the form of emulsion, lotion, paste etc.
3.Clean the metal parts with soft brush.
4.Do not wash the metal parts in dishwashers. Strong cleaning agents used in dishwashers cause the metal parts to turn black.
Handwash the metal parts using traditional washing-up liquid.
5.Don't clean the equipment mounted on the machine's drive assembly.
TECHNICAL DATA
Permitted continuous operation time: 10 minutes
Break time before another use: 30 minutes
Supply voltage: 220-240V~50Hz
Power: 350W
Max. power:1500W
4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler Ad 4808 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler Ad 4808 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 5,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info