799594
4
Zoom out
Zoom in
Previous page
1/68
Next page
4
immediately remove the power plug or power adaptor from the socket. If the device is
powered, do not put hands in the water. Have the device checked by the qualified
electrician before using it again.
18. Do not touch the device or power adaptor with wet hands.
19. The device has to be turned off after every use.
20. Do not leave the unit attached to the wall outlet or power supply unit unattended.
21. If the device utilises a power adaptor, do not cover it, because this can cause a
dangerous temperature rise and can damage the device. Always connect the power
adaptor cable to the device, and then connect the power adaptor to the power socket.
22. Keep the device out of the reach of children. Using the devices by children must be
supervised by adults.
23. The device is designed only for cutting natural human hair.
24. The cutting blades are very sharp. Be careful during assembly, disassembly and
cleaning. Do not touch the blades moving parts during operation!
25. Do not wash the blades in water.
26. Change the attachments only when the unit is turned off.
27. Use only original accessories.
28. To remove hair from inside the machine, use only the included brush.
29. Do not use the device in the bath.
30. Do not use the device on people who are sleeping.
31. During operation, do not place the device on wet surfaces or clothes.
32. The device is not designed to work with external schedulers or separate remote control
system.
DESCRIPTION OF THE DEVICE
1. Power switch 2. Clipping head 3.. Power / Charging light 5. Cutting length
attachments (1.5mm, 3mm, 4.5mm, 6mm.) 6. Protection cover 7. Oil
8. Cleaning brush 9. USB cable. 10. Charging port
BATTERY CHARGING
Before use, charge the battery. To begin charging, connect the power cord (9) to the devices Charging port and the USB cableto the
charger or other USB compatible device. Is using the charger plug it into an 5V 1A mains outlet. The charging icon will light up . A fully
charged battery is sufficient for up to 240 minutes of continuous operation. After charging, remove the charger from the power source.
When the device is not used for a long time please recharge. Recharge it at least once every 6 months to maintain adequate battery
capacity.
USING THE DEVICE
Depending on the needs install the appropriate trimmer attachment as shown in Figure B. To remove it follow the Figure B in reverse
order.
Blade removal:
Using a Philips screwdriver (cross shaped) unscrew the 2 screws from the blade as shown on picture D. Take a new blade and place it in
the same position as the previous blade. Making sure the holes and inside parts are correctly assembled screw the blade into place using
the same screws. Turn on the device to check if the blade is working correctly before use. Please check if the blades are parallel to each
other.
CLEANING
Disconnect the device from the power supply. Remove the attachment from the head. Clear the blades with the supplied brush. After
cleaning, there should be no hair between the blades. After every few haircuts, oil the cutting head pouring 2 to 3 drops of the supplied oil
into the space between the fixed blade and the movable blade. Install the Protection Cover (6). Clean the housing with a dry or slightly
damp cloth.
TECHNICAL DATA
Power supply: 5V 1A
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 2836 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 2836 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 4.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info