738836

Adler AD 2832 Manual

4
Zoom out
Zoom in
Previous page
1/56
Next page
device (RCD) in the power circuit, with residual current rating not more than 30 mA.
Contact professional electrician in this matter.
22. The cutting scissors are very sharp. Use caution when assembling, dismantling and
cleaning. Do not touch any elements of the moving blade during the operation!
23. Do not use the device for more than 10 minutes at a time. After 10 minutes have
elapsed, turn it off for approximately 5 minutes. DO NOT CHARGE THE BATTERY FOR
LONGER THAN 48 HOURS – this can cause irreversible damage to the battery.
24. The charging process should be conducted in temperatures between 5-35 degrees
Celsius.
25. Do not wash the blades in water.
26. Only change comb attachments when the device is switched off.
PRODUCT DESCRIPTION (FIG. 1)
1. 'On/off' button 2. Regulation of cutting length 3. Scale of regulation of cutting length 4. Charging indicator
5. Charger 6.Display
CHARGING THE BATTERY
Charge the battery before use. To begin charging plug the power cord into the trimmer's socket, and the charger into a 100-240 V 50/60
Hz mains power outlet. The charging indicator will light up (fig. 1.4). The light will remain on until the device is unplugged from mains
power. The first charge takes 8 hours; subsequent ones should last 4hours. A fully-charged battery lasts for approximately 180 minutes of
continuous use. After charging, unplug the charger from the socket. If the trimmer is not used for a long period of time, it should be
charged at least once every 6 months. In order to maintain adequate battery capacity. If the battery is flat, you can continue cutting using
the charger. To do this plug the charger cable into the trimmer socket. After 2 minutes you can continue cutting.
USING THE TRIMMER
Select the desired cutting length by turning the cutting length adjustment knob (fig. 1.2), observing the regulation scale (fig. 1.3).
To change the comb turn the trimmer off, unclip the comb (fig. 5) and clip on the right one (fig. 4).
Start cutting by running the trimmer with the comb attachment against the direction of hair growth. This should be done slowly and at a
steady speed. Please remember to regularly clean the trimmer and cutting head of any hair.
CLEANING
Unplug the device from the power source. Remove the cutting head (fig. 2). Clean the blade with the included brush. No hair should
remain between the blades after cleaning. Every few haircuts lubricate the cutting head by dropping 2-3 drops of the machine oil into the
space shown in fig. 6. Close the head (fig. 3). Clean the casing with a dry or slightly damp cloth.
Display information:
The display will show 4 information. 1. THe % state of the battery when it reaches 0 the device will turn off. 2. Turbo option the device will
work on higher RPM. 3. Loading (The icon will be red) the % load of battery will increase untill 100% and then will turn green and start
flashing. 4: and working under adaptor power (It will turn green) and not use battery.
15.If using the device in bathroom after use remove the power plug from the
socket, because water proximity presents risk, even if the device is turned off.
16. Do not allow the device or power adaptor to wet. If the device falls into water,
immediately remove the power plug or power adaptor from the socket. If the device is
powered, do not put hands in the water. Have the device checked by the qualified
electrician before using it again.
17. Do not touch the device or power adaptor with wet hands.
18. The device has to be turned off after every use.
19. Do not leave switched on equipment or adapter without supervision.
20. Never use this device close to water, e.g.: Under shower, in bathtube, or above
sink filled with water.
21. If the device utilises a power adaptor, do not cover it, because this can cause a
dangerous temperature rise and can damage the device. Always connect the power
adaptor cable to the device, and then connect the power adaptor to the power socket.
4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 2832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 2832 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 5,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info