799436
4
Zoom out
Zoom in
Previous page
1/92
Next page
4
Volume control:
4. You can also press and hold the Scan – and Scan + button (7,8) for the device to automatically find the next radio signal.
3 You can change the frequency by pressing the Scan – and Scan + button (7,8).
2. The device will turn on the radio function.
1. Turn the device on by pressing the STANDBY / FUNCTION button (2) once.
Radio setting:
3. TO turn off the device press and hold the STANDBY / FUNCTION button (2) .
2. The device will turn on.
1. Press the STANDBY / FUNCTION button (2) once.
Turning on the device:
1. Press and hold the "SNOOZE / DIMMER" button (6) for 2 seconds to select the dimmer. Dimmer has 3 steps.
This function can be used in both “Standby Mode” and “Turned On Mode”
NOTE:
Dimmer
The alarm will start again after approx. 9 minutes.
Press the “SNOOZE / DIMMER” button (6) to suspend alarm sound for a few minutes.
Snooze
3. The display (1) will also show the alarm current setting.
2. The dot next to the AL-1 or AL-2 respectfully on the left side of the display (1) to signal the alarm is turned on.
1. To turn on the alarm press the the Vol-/Vol+ / Al.1/Al.2 Button (4,5) button once.
Alarm turning On:
7. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
6. Choose the volume level of the Buzzer or Radio playing by pressing the SCAN +/- buttons (7,8).
5. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
4. Choose alarm type between BUZZ and TUNE. Buzzer or Radio. The radio choice will turn the last used radio station.
3. Confirm your choice with the Vol-/Vol+ / Al.1/Al.2 Button (4,5). button by pressing it once.
2. Choose time by pressing the SCAN – and SCAN + button (7,8).
1. Press and hold the Vol-/Vol+ / Al.1/Al.2 Button (4,5). The display (1) will start to blink.
Alarm 1/2 setup:
3. Confirm your choice with the CLK / MEM (3) button by pressing it once.
2. Choose time format 12 / 24 H by pressing the SCAN +/- buttons (7,8).
1. Press and hold the Clk. / MEM. Button (3). The display (1) will start to blink.
Clock setup:
5. Insert the device AC power cord (13) into the wall socket (220-240 V 50/60Hz.)
4. Close the backup battery door (14).
3. Insert 2 AAA 1.5V batteries in the position shown inside.
2. Open the backup battery door (14).
1. Remove all the packing material from the device.
Setting up the device:
Before powering the device on. Remove all packing material and read the instruction manual carefully. Keep it for future reference.
15. AUX-IN JACK 16. USB CHARGING PORT
13. AC POWER CORD 14. BACKUP BATTERY DOOR
11. WIRELESS CHARGE LOCATION 12. ANTENNA
9. SLEEP / PRESET button 10. PLAY / PAUSE button
7. SCAN- button 8. SCAN+ button
5. VOLUME+ / ALARM 2 button 6. SNOOZE / DIMMER button
3. CLOCK / MEMORY button 4. VOLUME- / ALARM 1 button .
1. DISPLAY 2. STANDBY / FUNCTION button
Device description (Clock radio):
17. The device should be kept in a dry room.
16. The device may only be wiped with a dry cloth. Do not use water or cleaning fluids.
15. Avoid getting the device wet.
device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact
professional electrician in this matter.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 1192 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 1192 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3.2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info