461421
55
Zoom out
Zoom in
Previous page
1/68
Next page
DOMINO 24 & 48 USER MANUAL
www.adblighting.com
User Manual - page 53
Issue 1.2
16.3 CONNECTED STL INDICATORS
To see all Submasters that are connected to an STL;
HOLD [function], tap [f/a] (stl 1) or (stl 2). HOLD [function].
Submaster connected to the selected STL flash continuously.
To see if an individual submaster is connected to any STL press;
[select], [f/a] (chaser number).
The video screen shows a pinned display of the selected chaser showing any connected
STL’s.
Press [select] to exit.
16.4 STL (SOUND TO LIGHT) MODE
When a chaser is connected to an STL that is in STL mode, the chasers own internal speed
generator continues to step the chaser in addition to the STL stepping from the audio signal.
To give the STL total control, set the chase speed to zero.
Hint; Set the chaser speed to be slower than the beat of the music. If the music stops, the
chaser will continue to run.
Connect a music source to the RCA audio input connector on the rear of the DOMINO. The
best source of audio from your device is the headphone socket as it provides a high level
signal (1-2.5V).
To select STL mode;
HOLD [function], tap [f/a] (stl 1) or (stl 2).
The display scrolls a message showing the current mode of the STL.
Tapping [yes], toggles the STL between either Sound to Light mode or SyncoBEAT mode.
To select STL mode, turn SyncoBEAT OFF.
The current mode of each STL is also shown at the bottom of the main video screen. The
”Volume Control” bargraph indicates STL mode as shown for STL1 in the example below.
The audio level and frequency can now be adjusted to make the chaser step to the beat of
the music.
To adjust the audio level press; [function].
The display shows “L: ##” where ## (0-100) is the audio level.
Rotate the EDIT wheel to adjust the level.
The volume control bargraph on the video also shows the current level. With the music
connected, the Level Bargraph will pulse up and down in time with the music.
Set the level so that the bargraph turns Yellow. Green is too low and Red is too high.
To adjust the audio frequency press; [function].
The display shows “hz ##” where ## (10-600) is the audio frequency.
Rotate the EDIT wheel to select the required frequency.
The Frequency indicator on the video also shows the current setting (low to high frequency).
“Volume Control”
bargraph indicates
STL mode and
shows current
“level setting”.
B” indicates
SyncoBEAT
mode
Frequency
indicator
Level Bar
g
ra
p
h
“Stepping” Beat indicator
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ADB Domino 48 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ADB Domino 48 in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ADB Domino 48

ADB Domino 48 User Manual - German - 72 pages

ADB Domino 48 User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info