Manual ACV SL 130 (page 20 of 40) (English)

525505

Zoom out

Zoom in

1/40

G3 REQUIREMENTS AND GUIDANCE

Discharge pipe from safety valves

The Building Regulation G3 requires that any discharge from an unvented system is con-

veyed to where it is visible, but will not cause danger to persons in or about the building.

The tundish and discharge pipes should be ﬁ tted in accordance with the requirements and

guidance notes of Building Regulation G3. The G3 Requirements and Guidance sections

3.50 - 3.63 are detailed below.

For discharge pipe arrangements not covered by G3 Guidance advice should be sought

from your local Building Control O cer.

Main characteristics :

• Any discharge pipe connected to the pressure relief devices (Expansion Valve and

Temperature/Pressure Relief Valve) must be installed in a continuously downward di-

rection and in a frost free environment.

• Water may drip from the discharge pipe of the pressure relief device.

• This pipe must be left open to the atmosphere.

• The pressure relief device is to be operated regularly to remove lime deposits and to

verify that it is not blocked.

A typical discharge pipe arrangement is shown on next page.

General remarks

• Discharge pipe-work D2 can now be a plastic pipe but only pipes that have

been tested to a minimum 110°C must be used.

• Discharge pipe D2 can now be plumbed into the soil stack but only soil stacks

that can handle temperatures of 99°C or greater should be used.

Extract from “The Building Regulation G3” :

Discharge pipe D1

3.50 Safety devices such as temperature relief valves or combined temperature and pres-

sure and pressure relief valves (see paragraphs 3.13 or 3.18) should discharge either

directly or by way of a manifold via a short length of metal pipe (D1) to a tundish.

3.51 The diameter of discharge pipe (D1) should be not less than the nominal outlet size of

the temperature relief valve.

3.52 Where a manifold is used it should be sized to accept and discharge the total di-

scharge from the discharge pipes connected to it.

3.53 Where valves other than the temperature and pressure relief valve from a single

unvented hot water system discharge by way of the same manifold that is used by the

safety devices, the manifold should be factory fitted as part of the hot water storage

system unit or package.

Tundish

3.54 The tundish should be vertical, located in the same space as the unvented hot water

storage system and be fitted as close as possible to, and lower than, the valve, with

no more than 600mm of pipe between the valve outlet and the tundish.

Note: To comply with the Water Supply (Water Fittings) Regulations, the tundish should in-

corporate a suitable air gap.

Smart SL-SLEW : A1007850 - 661Y1700 • F - draft

Installation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ACV SL 130 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ACV SL 130

ACV SL 130 User Manual - German - 36 pages

ACV SL 130 User Manual - Dutch - 36 pages

ACV SL 130 User Manual - Dutch - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ACV SL 130 Manual

Product: