524655
19
Zoom out
Zoom in
Previous page
1/26
Next page
ENFRRU PL DE IT ES NL
EN • 19
664Y5400B
ANNUAL MAINTENANCE
ACV recommends the boilers should be serviced at least once a year.
Maintenance and the burner control must be performed by a qualified
engineer.
More frequent servicing may be required depending on boiler use. If this
is the case, consult your installer for advice.
BOILER MAINTENANCE
1. Put the master switch on the control panel on "OFF" and isolate
power supply to the unit.
2. Turn off the gas or oil supply to the boiler.
3. Remove the flue pipe to gain access to the top of the boiler
4. Remove the casing top panel and lift off the flue reduction collar by
releasing the fastening bolts.
5. Remove the turbulators from the flue pipes for cleaning.
6. Unscrew the burner chamber plate and remove the burner
7. Brush the flue pipes.
8. Clean the burner chamber and the burner.
9. Reassemble turbulators, flue reduction collar and flue pipe,
checking that the gasket of the flue reduction collar is in good
condition. Replace gasket if necessary.
MAINTENANCE OF THE SAFETY DEVICES
- Check that all thermostats and safety devices are working properly.
- Test the safety valves on the central heating and hot water circuits.
SERVICING THE BURNER
For all burners, please refer to the relevant servicing and troubleshooting
instructions in the technical manual of your burner.
DRAINING THE BOILER
Water flowing out of the drain valve may be extremely hot
and could cause severe scalding.
Keep people away from discharge of hot water.
DRAINING THE HEATING CIRCUIT
1. Put the master switch of the control panel on OFF, isolate the
external electrical supply and turn off the gas or oil supply to the
boiler.
2. Close the isolating valves (4) or put manually the 4-way mixing valve
(1) on “0.
3. Connect a hose to the draining valve (7).
4. Open the draining valve to empty the primary circuit.
DRAINING THE DHW CIRCUIT
1. Put the master switch of the control panel on OFF, isolate the
external electrical supply and turn off the gas or oil supply to the
boiler.
2. Release the pressure in the heating circuit until the pressure gauge
indicates 0 bar.
3. Close valves (1) and (8).
4. Open valves (9) and (10) (first 9 then 10).
5. Allow the drained water to flow into the sewer.
For the circuit to be drained, the draining valve (9) must
be located at ground level.
MAINTENANCE
1
7
8
44
2
5
I
O
6
6
3
10
9
12
11
1 2
3
4
5
2
6
7
8
9
10
11
I
O
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ACV HEATMASTER 70 N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ACV HEATMASTER 70 N in the language / languages: English as an attachment in your email.

The manual is 8,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ACV HEATMASTER 70 N

ACV HEATMASTER 70 N User Manual - German - 26 pages

ACV HEATMASTER 70 N User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info