771220
17
Zoom out
Zoom in
Previous page
1/28
Next page
STARTING UP
Before starting up your appliance, it is necessary to bleed the boiler, the pipes and the faucets
completely because air can be present in them.
For this, before putting the boiler under voltage, fill up the appliance by opening the stopcock of
the safety group and by keeping one of the hot water taps open if there are several of them. Let
the water flow until it is perfectly clear.
Switch on the appliance. During warming up, the expansion of water may cause flow-out from the
safety group.
It is recommended that the various functions should be controlled at least once every year.
THERMOSTAT
The thermostat which allows holding the temperature of the volume of water can be adjusted
between 20
o
C and 65
o
C
In order to prevent the generation of legionella bacteria, the thermostat is factory-set to 65
o
C.
The thermal security integrated into the thermostat helps avoiding all kinds of incidental
overheating.
Where the security thermostat switches off, the installation technician should first search the
trouble and realise troubleshooting and then switch the appliance on.
ADVICE FOR THE USERS
MAINTENANCE
Before doing any interventions on the appliance, disconnect the appliance from the electric supply.
The shielded resistance and the anode are mounted on the dismantling flange therefore they can
be accessed to easily.
In order to drain the boiler, close the stopcock (A) of the safety group, open the draining tap B,
then open the hot water tap.
In order that the protection against corrosion should be more efficient, the boiler is equipped with
an anode.
The longevity of the anode depends on the agressivity of water and the normal usage temperature.
We recommend you to examine the condition of the anode periodically at least two years after the
start-up.
If the diameter of the anode (which is 32 mm normally) is equal to or less than 10 mm even on
only one point, it is compulsory to replace theanode.
If the water is very hard, it is advised to remove the scale from the boiler every year:
- drain the appliance then take off the flange,
- take off the scale appearing in the form of mud or laminae from the bottom of the tank then
clean the thermostat and the heating elementcarefully.
Do not try to take off the scale adhering to the side-wall of the tank because it constitutes efficient
protection from corrosion.
We assume no liability for damages which arise from the user's failure to comply with these
instructions.
HYDRAULIC SECURITY GROUP
Each month, move all the taps and the safety valve but always take back.
- stopcock A to the open position.
- the draining tap B to the closed position.
Please, check also the proper functioning of the safety valve. (Owing to the expansion of water occurring after
heating, in general the flow should be observed at the opening of the valve)
ENG
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ACV Glass BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ACV Glass BL in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 0.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info