677376
12
Zoom out
Zoom in
Previous page
1/48
Next page
en
12
EN
FR
NL
ES
IT
DE
PL
RU
BMV3 / BMV4 / BMV5 : 662Y1000 • A
7. TROUBLESHOOTING
Diagnostic Cause Remedy
1 . Oil firing unit
Error signal lamp is not on
No voltage present
Boiler temperature controller incorrectly adjusted
Check wiring
Adjust
Error signal lamp on
Oil firing unit switched to malfunction
Oil firing unit defective
Incorrect wiring of terminal socket
Correct malfunction
Replace
Check wiring
Check oil pre-heater
2 . Motor
Motor does not start
Defective release thermostat of oil pre-heater
Defective capacitor
Stiff bearing
Stiff oil pump
Replace oil pre-heater
Replace capacitor
Replace motor
Replace oil pump
Loud noise caused by running motor
Motor defective
Bearing defective
Oil pump defective
Replace motor
Replace motor
Replace oil pump
3 . Ignition
No generation of ignition sparks
Ignition unit defective
Ignition cable defective
Oil firing unit defective
Insulator defective
Replace ignition unit
Replace ignition cable
Replace oil firing unit
Replace ignition electrodes
Weak ignition spark
Incorrect position of the ignition electrodes
Ignition electrodes severely contaminated
Position ignition electrodes
Clean ignition electrodes
4 . Oil pump
Inconsistent oil pressure, loud noise
from operating oil pump, no oil
pressure is built up
Intake pipe leaking (air entry)
Oil supply not according to the specifications
Intake pipe containing air
Oil stop valve closed
Coupling defective
Oil pump filter dirty
Oil pump drive defective
Paraffin sedimentation (+4 °C)
Fuel oil viscous (-1 °C)
Check oil supply
Check oil supply
Purge intake pipe
Open stop valve
Replace coupling
Clean/replace oil pump filter
Replace oil pump
Install at a frost-free place
Install at a frost-free place
5 . Magnetic valve
Magnetic valve does not open
Coil of the magnetic valve defective
Oil firing unit defective
Replace coil of the magnetic valve
Replace oil firing unit
6 . Flame monitoring
Fault shut-down without flame
generation
Extraneous light (photocell current >5,5 μA)
Photo conductive cell defective
Remove extraneous light
Replace photocell
Fault shut-down with flame generation
Photo conductive cell contaminated
Photocell current too weak (photocell current < 55 μA)
Clean photocell
Reset burner
7 . Nozzle
Inconsistent atomisation, high CO
and soot emissions
Defective nozzle
Oil pressure not in compliance with specification
Diaphragm valve defective
Replace nozzle
Adjust oil pressure
Replace oil pre-heater
8 . Baffle plate
Baffle plate / burner pipe very
contaminated
Incorrect burner adjustment
Inconsistent atomisation of the nozzle
Adjust burner
Replace nozzle
Replace oil pre-heater
Nozzle is dripping Replace oil pre-heater
Incorrect nozzle type (spraying angle, spraying
characteristics, installation size)
Insert nozzle according to specification
9 . Fan
Fan delivers not enough air
Fan wheel contaminated
Fan wheel damaged
Clean fan wheel
Replace fan wheel
Loud noise during fan operation
Fan wheel incorrectly positioned
Fan wheel damaged
Air flap incorrectly installed
Correctly position fan wheel
Replace fan wheel
Correctly install air flap
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ACV BMV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ACV BMV in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 3,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info