646707
5
Zoom out
Zoom in
Previous page
1/44
Next page
2
1.1 ON/OFF Button
Starting Operation:
When the unit is turned off, press the ON/OFF button.
The operation LED lights and the unit is turned on.
Stopping Operation:
When the unit is turned on, press the ON/OFF button. The operation LED is extinguished
and control are turned off.
1.2 SLEEP Button
Press SLEEP button to activate the sleep mode or energy saving mode.
1.3 FAN Button
Press FAN button to select
AUTO
,
HIGH
,
MEDIUM
or
LOW
fan speed.
1.4 MODE Button
Press the MODE button to switch operation from
COOL
,
HEAT
,
AUTO, DRY
,
FAN
.
The Auto mode is unavailable for Chilled Water (CW) system.
Check the display to see in which mode the control is set.
1.5 or ‘’ Set Temperature Button
Press the temperature button and set the temperature of your choice. By pressing the ‘’ or
’ button once, temperature changes by 1°C [or 1°F].
Temperature can be set within the range 16°C~30°C (61°F~86°F) or 20°C~30°C (68°F~86°F).
The range can be set by adjusting the shunt jumper behind the LCD remote (refer table below).
During fan mode, temperature can not be set.
If pressing ‘’ and ‘ together, the unit of temperature will change from °C to °F and
vice-versa.
1.6 SWING button
Press SWING button to activate the air sweep function.
1.7 Time Setting
i) Set Real Time Clock Setting
Press CLOCK key one time will activate RTC setting mode. Pressing the same key again
will disable RTC setting mode.
Under RTC setting mode, “SET CLOCK” will be shown on LCD and it will blink at 0.5 sec
interval. The RTC and Day setting can be changed by pressing DAY key, HOUR key or
MINUTE key. If there is no further time related (DAY, HOUR and MINUTE) key is pressed
for 15 sec, the unit will quit from the CLOCK setting mode.
ii) 7-Day Programmable Timers
The unit has 3 event functions, each event has an ON TIMER and an OFF TIMER.
Press the timer key (ON TIMER or OFF TIMER) will enable Event 1 timer setting mode.
Press the same key again will enable Event 2 timer setting mode. Press the 3rd times will
enable the Event 3 (Event handset) timer- setting mode. Subsequent key pressed the unit
will quit from timer setting mode.
All timers are event triggered timers and can be overridden by the ON/OFF button and
Override function.
iii) Set Event 1 and Event 2 Timers
Under timer setting mode, “SET TIMER” will be shown on LCD and blink at 0.5 sec interval.
For Event 1 Timer setting, ‘ ON’ or ‘ OFF’ indication will appear and digit “1” will be
displayed on the top left corner of the LCD. ‘ ON’ or ‘ OFF’ indication and digit “2”
will be displayed during Event 2 timer setting. The timer setting can be changed through
pressing the DAY key, HOUR key or MINUTE key. If there is no further time related (DAY,
HOUR and MINUTE) key is pressed, the unit will quit from the timer setting mode.
Jumper 20 - 30 Application
SET Set temp range : 20°C ~ 30°C (68°F ~ 86°F)
OFF Set temp range : 16°C ~ 30°C (61°F ~ 86°F)
1 OM-NET3-0808_EN 9/5/08, 12:00 PM2
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Acson NET3-0808 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Acson NET3-0808 in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info