Manual Acronis true image 9 1 server bundle (page 73 of 81) (English)

258699

Zoom out

Zoom in

1/81

Hard disks with an IDE (Integrated Drive Electronics) interface are connected to the

motherboard via a 40- or 80-thread flat marked cable: one of the threads of the

cable is red.

Two IDE hard disks can be connected to each of the sockets, i.e. there can be up to

four hard disks of this type installed in the PC. (There are three plugs on each IDE

cable: two for hard disks and one for the motherboard socket.)

As noted, IDE cable plugs are usually designed so that there is only one way to

connect them to the sockets. Usually, one of the pinholes is filled on the cable plug,

and one of the pins facing the filled hole is removed from the motherboard socket,

so it becomes not possible to plug the cable in the wrong way.

In other cases, there is a jut on the plug on the cable, and an indentation in the

socket of the hard disk and of the motherboard. This also ensures that there only

one way to connect the hard disk and the motherboard.

In the past, this design of plug did not exist, so there was an empirical rule: the

IDE cable is connected to the hard disk socket so that the marked thread

is the closest to the power cable, i.e. the marked thread connected to pin #1 of

the socket. A similar rule was used for connecting cables with the motherboard.

Incorrect connection of the cable with either the hard disk or the motherboard does

not necessarily damage the electronics of the disk or the motherboard. The hard

disk is simply not detected or initialized by BIOS.

here are some models of hard disks, especially the older ones, for which incorrect

connection damaged the electronics of the drive.

We will not describe all the types of hard disks. Currently the most widespread are those

with IDE or SCSI interfaces. Unlike IDE hard disks, there can be from six to 14 SCSI hard

disks installed in your PC. However, you need a special SCSI controller (called a host

adapter) to connect them. SCSI hard disks are not usually used in personal computers

(workstations), but are found mostly in servers.

Aside from an IDE cable, a four-thread power cable must be connected to the hard

disks. There is only one way to plug in this cable.

B.1.3 Installation modes, jumpers

A hard disk can be installed in a computer as master or as slave. The mode of hard

disk installation is defined by the position of special connectors (called jumpers) on

the hard disk.

The jumpers are either located on the electronic board of the hard disk or a special

socket that provides for the connection of the hard disk and the motherboard.

There is usually a sticker on the drive that explains the markings. Typical markings

are

DS, SP, CS and PK.

Each jumper position corresponds to one hard disk(s) installation mode:

•

DS – master/factory default

• SP – slave (or no jumper required)

• CS – cable select for master/slave: the purpose of the hard disk is determined by

its physical position with respect to the motherboard

• PK – jumper parking position: the position where one can put the jumper if it is

not necessary in the existing configuration

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Acronis true image 9 1 server bundle in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Acronis true image 9 1 server bundle

Acronis true image 9 1 server bundle User Manual - German - 140 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Acronis true image 9 1 server bundle Manual

Product: