284412

Acronis disk director suite 10 Manual

44
Zoom out
Zoom in
Previous page
1/96
Next page
44 Copyright © Acronis, Inc., 2000-2010
To perform the pending operation you will have to commit it (p. 20). Exiting the program without
committing the pending operations will effectively cancel them.
5.24 Unhiding a volume
This operation applies to hidden volumes on basic MBR disks.
Unhiding a hidden a volume means changing the volume type so that it will be visible by the
operating system. You may want to unhide a volume in order to:
Make a previously hidden volume again visible to the operating system.
Access data and make changes to files stored on a hidden OEM volume.
To unhide a volume
1. Right-click the hidden volume you need to unhide, and then click Unhide volume. The program
automatically assigns the first vacant drive letter to this volume.
2. Click OK to add the pending volume unhiding operation.
The results of the pending operation are immediately displayed as if the operation had been
performed.
To perform the pending operation you will have to commit it (p. 20). Exiting the program without
committing the pending operations will effectively cancel them.
5.25 Specifying i-node density
This operation applies to volumes whose file systems are Ext2 or Ext3.
The i-node is the main data structure for Linux Ext2/Ext3. All of a files information, with the
exception of its actual name and data, is stored in the i-node. Each file has its own i-node. Each i-
node contains a file description, including number, file type, size, data block pointers, etc. Space for i-
nodes is allocated when you install the operating system or when a new file system is created. The
maximum number of i-nodes, and hence the maximum number of files, is set at file system creation.
Running out of i-nodes prohibits the creation of additional files and directories on the volume even if
there is sufficient disk space. I-nodes themselves consume disk space, so specifying the i-node
density lets you organize disk space in the optimal way. I-node density is determined by specifying
the number of bytes per i-node. Usually, the default value is 4096 bytes per i-node.
Important: If you change the i-node density of a boot volume the operating system will become unbootable. To
restore the system bootability use a boot loader.
To specify i-node density
1. Right-click the Ext2/Ext3 volume, and then click Change i-node density.
2. In Bytes per i-node, specify the required value.
Use lower i-node density (that is, increased Bytes per i-node value) for a volume that
contains just a few large files. This will allocate more space for files and less for i-nodes. The
less i-nodes there are the in the system, the faster the “file system check” operation will be
performed.
Use higher i-node density (that is, reduced Bytes per i-node value) for volumes that contain a
large number of small files. This will allocate more space for i-nodes and less for data. The
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Acronis disk director suite 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Acronis disk director suite 10 in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Acronis disk director suite 10

Acronis disk director suite 10 User Manual - German - 113 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info