624416

Acronis Backup Advanced Version 11.5 Update 6 Manual

45
Zoom out
Zoom in
Previous page
1/449
Next page
45 Copyright © Acronis International GmbH, 2002-2015
3.7.2.4 Assembling MD devices for recovery (Linux)
In Linux, when performing recovery from a disk backup to an existing MD device (also called Linux
Software RAID), make sure that this device is assembled at the time of recovery.
If the device is not assembled, assemble it by using the mdadm utility. Here are two examples:
Example 1. The following command assembles the device /dev/md0 combined from the volumes
/dev/sdb1 and /dev/sdc1:
mdadm --assemble /dev/md0 -ayes /dev/sdb1 /sdc1
Example 2. The following command assembles the device /dev/md0 combined from the disks
/dev/sdb and /dev/sdc:
mdadm --assemble /dev/md0 -ayes /dev/sdb /dev/sdc
If the recovery requires the machine to be rebooted (usually, when the volumes to recover include
the boot partition), follow these guidelines:
If all parts of the MD device are volumes (a typical case, such as in the first example), make sure
that each volume type—called partition type or system ID—is Linux raid automount; the
hexadecimal code of this partition type is 0xFD. This will guarantee that the device will be
automatically assembled following the reboot. To view or change the partition type, use a disk
partitioning utility such as fdisk.
Otherwise (such as in the second example), perform the recovery from bootable media. No
reboot will be required in that case. In bootable media, you may need to create the MD device
manually or automatically, as described in Recovering MD devices and logical volumes (p. 45).
3.7.2.5 Recovering MD devices and logical volumes
Recovering MD devices and/or volumes created by Logical Volume Manager (logical volumes)
assumes that the corresponding volume structure will be recreated.
In Linux-based bootable media, you can choose to recreate the volume structure automatically (p.
46).
This functionality is intended primarily for bare-metal recovery of an entire machine. The software
backs up and recreates the entire logical volume structure, even if not all MD devices or logical
volumes are being backed up or recovered. Therefore, you need at least as many disks as the original
volume structure used.
Do not try to recreate the volume structure automatically in any of the following cases:
The machine has data that must be preserved. The software will destroy all data on the disks
that it chooses to recreate the volume structure on.
The machine has fewer physical disks than the original volume structure used. The software will
fail to recreate the volume structure even if the capacity of the physical disks is enough to fit all
the data being recovered.
The backup does not contain the volume structure information. This information might be
absent in backups created by Acronis Backup & Recovery 10, because saving it was optional.
In these cases, create the volume structure manually (p. 46) prior to recovery. You can do this by
using the mdadm and lvm utilities, either in Linux-based bootable media or in Linux.
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Acronis Backup Advanced Version 11.5 Update 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Acronis Backup Advanced Version 11.5 Update 6 in the language / languages: English as an attachment in your email.

The manual is 4,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Acronis Backup Advanced Version 11.5 Update 6

Acronis Backup Advanced Version 11.5 Update 6 Quick start guide - English - 13 pages

Acronis Backup Advanced Version 11.5 Update 6 Installation Guide - English - 67 pages

Acronis Backup Advanced Version 11.5 Update 6 Quick start guide - German - 14 pages

Acronis Backup Advanced Version 11.5 Update 6 User Manual - German - 73 pages

Acronis Backup Advanced Version 11.5 Update 6 User Manual - German - 506 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info