660209
9
Zoom out
Zoom in
Previous page
1/19
Next page
9
Double Pad Programs
The oven control can be changed to
store up to 100 cooking programs.
See the “User’s Options” section of this
manual to change oven control.
To start a double pad cooking program, press 2 memory
pads. For example, press pad 0 and pad 3 to start a
cooking program.
Manual Time Entry
Manual Time Entry feature allows the operator
to enter time and power levels, and heat without
changing the preprogrammed pads. Example: Heat for
30 seconds at 80% power.
1. Open oven door, place food in oven, and close door.
• Display shows “READY”. Fan and light operate.
• If pad is not pressed in 60 seconds, open and
close oven door again.
2. Press TIME ENTRY pad.
• Display shows “00:00” and “READY”.
3. Press 3 and 0 pad to enter cooking time.
4. Press POWER LEVEL pad to change
power level.
• Display shows “% MW POWER” and current
power level if other than 100 percent power.
5. Press 8 pad to enter desired power level.
6. Press START pad.
• Oven operates and time counts down.
• Display shows cooking time, “COOKING”, “% MW
POWER”.
• Display shows “COOKING” only when microwave
energy is present.
• If power level other than 100 percent power was
programmed, display shows “COOKING” and “%
MW POWER”. Display counts down cooking time.
7. Oven stops cooking and oven signal sounds when
cooking timing elapses and display shows “DONE”.
Memory Pads
From the factory, this oven can of store up to 10
cooking programs. Follow instructions below to program
cooking times and power levels for customized cooking.
Example: Program third cooking sequence to heat for 30
seconds at 80% power.
1. Open oven door.
• Display shows “DOOR”.
• If door is closed or STOP/RESET pad is
pressed before nishing programming sequence,
oven exits programming mode.
Operation
Interrupting Operation
Open oven door or press STOP/RESET pad to
interrupt operation. Display continues to show
countdown time. Close door and press START pad
to resume oven operation.
Canceling Mistakes
If oven is not cooking, press STOP/RESET pad to
clear display. If oven is cooking, press STOP/RESET
pad once to stop oven, then again to clear display. If
oven door is open and time shows in display, close oven
door and press STOP/RESET pad to clear display.
Operating Preprogrammed Pads
From the factory, this oven can of store up to 10
preprogrammed cooking sequences in memory.
To heat using a preprogrammed sequence,
press a numbered pad. Oven starts to heat
automatically. Example: Heat using the third cooking
sequence.
1. Open oven door, place food in oven, and close oven
door.
• Display shows “READY”.
• If pad is not pressed in 60 seconds, open and
close oven door again.
2. Press 3 pad.
• Oven operates and time counts down.
• Display shows cooking time, “STAGE 1”,
”COOKING”. Display shows “COOKING” only
when microwave energy is present.
• If power level other than 100 percent power
was programmed, display shows “STAGE 1”,
“COOKING” and “% MW POWER”.
• If additional cooking time is required, press
preprogrammed pads before or after cooking cycle
ends.
3. Oven stops cooking and oven signal sounds when
cooking timing elapses.
Preprogrammed Times and Cook Level
All preprogrammed pads arrive set at full power.
STYLE 1
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ACP MDC182 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ACP MDC182 in the language / languages: English as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ACP MDC182

ACP MDC182 User Manual - German - 19 pages

ACP MDC182 User Manual - French - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info