660203
10
Zoom out
Zoom in
Previous page
1/19
Next page
10
2. Press and hold pad 1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
“PROGRAM”.
3. Press 3 pad to select memory pad.
• Display shows cooking time, “STAGE 1” and
power level if other than 100 percent power.
4. Press 3 and 0 pad to enter desired cooking time.
5. Press POWER LEVEL pad to change
power level.
• Display shows cooking time and current power
level if other than 100 percent power.
6. Press 8 pad to enter desired power level.
Note: Press POWER LEVEL twice to reset to
100% power.
7. Press START pad to save new cooking time
and power level in oven memory.
• Display shows “PROGRAM”.
• Repeat step 3–8 to program additional pads.
8. Press STOP/RESET pad or close oven door
to exit programming mode.
Double Pad Programs
The oven control can be changed to store up to 100
cooking programs. See the “User’s Options” section of
this manual to change oven control.
To create a double pad program, follow the instructions
above except for a change to step #3. When entering
the cooking program number, press 2
memory pads. For example, press pads
0 and pad 3 to create a new cooking
program.
Multiple Cooking Stages
Follow instructions below to program oven to perform
four consecutive cooking cycles without interruption.
Example: Program third cooking sequence to heat for 30
seconds at 80% power, 40 seconds at 50% power, and
10 seconds at 100% power.
1. Open oven door.
• Display shows “READY”.
• If door is closed or STOP/RESET pad is
pressed before nishing programming sequence,
oven exits programming mode.
2. Press pad 1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
“PROGRAM”.
4. Press 3 pad to select memory pad.
• Display shows “P03”briey then cooking time,
“STAGE 1” and power level if other than 100
percent power.
5. Press 3 and 0 to enter desired cooking time.
6. Press POWER LEVEL pad to change
power level.
• Display shows “% MW POWER” and current
power level if other than 100 percent power.
7. Press 8 pad to enter desired power level.
8. Press TIME ENTRY pad.
• Display shows cooking time, and “STAGE 2”
indicating programming stage 2 and power level
for stage shown in display.
• Repeat steps 5–8 to create additional stages.
9. Press START pad to save new cooking time
and power level in oven memory.
10. Press STOP/RESET pad or close oven door
to exit programming mode.
Programming
STYLE 1
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ACP HDC12A2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ACP HDC12A2 in the language / languages: English as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ACP HDC12A2

ACP HDC12A2 User Manual - German - 19 pages

ACP HDC12A2 User Manual - French - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info